Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1256/56    Accumulator Low Pressure

for Preparation Click here


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.
The skid control ECU turns on the brake warning light / red (malfunction) and brake warning light / yellow (minor malfunction), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.
DTC C1256/56 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1256/56
341
Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.)
  1. Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)
  2. Pump motor malfunction
  3. Accumulator deterioration
  4. Accumulator pressure sensor (Brake booster with master cylinder assembly)
  5. Supply voltage reduced

WIRING DIAGRAM

Refer to DTCs C1252/52 and C1253/53 .

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 are output together with C1256/56, inspect and repair the trouble areas indicated by C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 first (Click here, Click here, Click here, or Click here).

1.BRAKE PROBLEM CHECK
  1. Ask the customer if frequent braking was performed while the brake warning light / yellow (minor malfunction) was on.

    OK:

    Result
    Proceed to
    Frequent braking was not performed.
    A
    Frequent braking was performed.
    B

    HINT:
    This DTC may be stored even if the accumulator pressure drops only temporarily due to frequent braking.



B
END
A


2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY


    C243137E04
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the brake booster pump assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A45-1 (BM1) - A45-2 (GND1)
    Always
    Below 10 Ω
    A46-2 (BM2) - A46-1 (GND2)
    Always
    Below 10 Ω
    A45-1 (BM1) - A46-2 (BM2)
    Always
    Below 1 Ω
    A45-2 (GND1) - A46-1 (GND2)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Booster Pump Assembly)



NG
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)
OK


3.READ VALUE USING TECHSTREAM (ACCUMULATOR PRESSURE SENSOR)
  1. Reconnect the brake booster pump assembly connectors.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Select the Data List on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor /
    Min.: 0.00 V, Max.: 5.00 V
    Specified value: 2.90 to 4.20 V
    When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator

  1. Wait for 30 seconds without depressing the brake pedal.

  1. Check that the accumulator pressure sensor output value change is within the specified range.

    OK:
    Accumulator pressure sensor output value change is less than 0.55 V.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.PERFORM ACTIVE TEST USING TECHSTREAM (SOLENOID VALVE)
  1. Select the Active Test on the Techstream (Click here).

    HINT:
    The Active Test can be performed when the following conditions are met.
    1. ABS main relay is on.
    2. Shift lever is in P.
    3. Parking brake is applied.
    4. Vehicle speed is 0 km/h (0 mph).


    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Solenoid (SMC/SRC/SCC)
    Switching solenoid valve (SMC/SRC/SCC)
    Solenoid ON/OFF
    Operation sound of solenoid (clicking sound) can be heard
    *: Electronically Controlled Brake System

  1. Perform the Active Test of the solenoid using the Techstream.

  1. Select the Data List on the Techstream (Click here).


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Wheel Cylinder Pressure Sensor
Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.10 to 0.90 V
Reading increases when brake pedal is depressed
  1. Check that the output value of the wheel cylinder pressure sensor does not increase.

    OK:
    The output value of the wheel cylinder pressure sensor does not increase.

    HINT:
    If the output value increases, there may be brake fluid leaks in the brake actuator.



NG
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
OK

REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)