Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Malfunction in Water Temperature Warning Light

for Preparation Click here


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication system. The combination meter assembly displays an engine coolant temperature warnings based on the data received from the ECM.

WIRING DIAGRAM


E143765E63


INSPECTION PROCEDURE

HINT:
  1. If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI system (Click here).
  2. If the exhaust heat recirculation system has a malfunction, the water temperature warning comes on to inform the driver of the malfunction.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTCs are output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTCs are not output.
    A
    CAN communication DTCs are output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK FOR DTC
  1. Check for DTCs (Click here for SFI System, Click here for Meter/Gauge System).

    Result:
    Result
    Proceed to
    DTCs are not output.
    A
    SFI system DTCs are output.
    B
    DTC B1503 is output.
    C



B
GO TO SFI SYSTEM (Click here)

C
GO TO METER / GAUGE SYSTEM (Click here)
A


3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE, COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus:

    1. for Combination Meter: Body Electrical / Combination Meter / Data List.

    2. for Engine: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F)
    After warming up: 75 to 100°C (167 to 212°F)
    -

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Stored as Freeze Frame Data
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    Stored as Freeze Frame Data
    1. Stored as Freeze Frame Data
    2. This is the engine coolant temperature
    Diagnostic Note:
    This is the engine coolant temperature.

    HINT:
    1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
    2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    3. If the value is -40°C (-40°F) or higher than 135°C (275°F), the sensor circuit may be open or shorted.
    4. Check if the engine overheats when the value indicates higher than 135°C (275°F).

    NOTICE:
    Enter inspection mode (Click here).


    Result:

    Result
    Proceed to
    The data list values of the ECUs do not match.
    A
    The data list values of the ECUs match.
    B

    HINT:
    When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.



B
GO TO SFI SYSTEM (Click here)
A


4.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or a known good one (Click here).

    OK:
    The operation of the water temperature warning returns to normal.



NG
REPLACE ECM (Click here)
OK

END