CAN COMMUNICATION SYSTEM > Open in CAN Main Bus Line |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. |
|

| 1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G4-6 (CANH) - G4-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH) |
![]() |
Disconnect the G1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G1-31 (CANH) -G1-32 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | ||
| ||
| 3.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN J/C LH) |
Reconnect the G1 combination meter assembly connector.
![]() |
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-13 (CANH) - A40-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C RH) |
Reconnect the A40 ECM connector.
![]() |
Disconnect the G72 CAN junction connector RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| G72-7 (CANH) - G72-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Combination meter assembly |
| G72-10 (CANH) - G72-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | CAN junction connector LH |
| *a | Front view of wire harness connector (to CAN Junction Connector RH) |
| *b | to Combination Meter Assembly |
| *c | to CAN Junction Connector LH |
| Result | Proceed to |
| OK | A |
| NG (Combination meter assembly main line) | B |
| NG (CAN junction connector LH main line) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE)) |
Reconnect the G72 CAN junction connector RH.
![]() |
Disconnect the G71 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| G71-4 (CANH) - G71-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | CAN junction connector RH |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to CAN Junction Connector RH |
|
| ||||
| OK | |
| 6.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE)) |
Reconnect the G71 CAN junction connector LH (instrument panel wire side).
![]() |
Disconnect the A51 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A51-9 (CANH) - A51-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to ECM |
|
| ||||
| OK | ||
| ||