Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

  1. w/o Sliding Roof:
    Using this circuit, the radio receiver assembly sends power to the amplifier microphone assembly, and the amplifier microphone assembly sends microphone signals to the radio receiver assembly.
  2. w/ Sliding Roof:
    Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the roof console box assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM


w/o Sliding Roof

E204785E09


w/ Sliding Roof

E204785E10


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:

Result
Proceed to
w/o Sliding Roof
A
w/ Sliding Roof
B



B
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
  1. Disconnect the radio receiver assembly and amplifier microphone assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-6 (SNS2) - Q5-4 (SNS2)
    Always
    Below 1 Ω
    G41-4 (MACC) - Q5-1 (MACC)
    Always
    Below 1 Ω
    G41-5 (MIN+) - Q5-2 (MCO+)
    Always
    Below 1 Ω
    G41-19 (MIN-) - Q5-3 (MCO-)
    Always
    Below 1 Ω
    G41-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G41-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    G41-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    G41-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    G41-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT RADIO RECEIVER ASSEMBLY
  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the amplifier microphone assembly connector.



    E237416E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G41-4 (MACC) - Body ground
    Ignition switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-18 (SGND) - Body ground
    Always
    Below 1 Ω
    G41-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


4.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
  1. Disconnect the amplifier microphone assembly connector.



    E244512E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q5-3 (MCO-) - Q5-4 (SNS2)
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Amplifier Microphone Assembly)


NG
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
OK


5.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
  1. Reconnect the radio receiver assembly connector.



    E244513E01
  1. Reconnect the amplifier microphone assembly connector.

  1. Turn the ignition switch to ON (ACC).

  1. Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-) of the amplifier microphone assembly connector.

  1. Check the waveform of the amplifier microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the amplifier microphone assembly is output
    A
    A waveform synchronized with the voice input to the amplifier microphone assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Amplifier Microphone Assembly)


B
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
A

END 

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the radio receiver assembly and map light assembly (telephone microphone assembly) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-6 (SNS2) - Q4-12 (SNS2)
    Always
    Below 1 Ω
    G41-4 (MACC) - Q4-4 (MACC)
    Always
    Below 1 Ω
    G41-5 (MIN+) - Q4-5 (MCO+)
    Always
    Below 1 Ω
    G41-19 (MIN-) - Q4-6 (MCO-)
    Always
    Below 1 Ω
    G41-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G41-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    G41-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    G41-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    G41-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT RADIO RECEIVER ASSEMBLY
  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the map light assembly (telephone microphone assembly) connector.



    E237416E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G41-4 (MACC) - Body ground
    Ignition switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-18 (SGND) - Body ground
    Always
    Below 1 Ω
    G41-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the map light assembly (telephone microphone assembly) connector.



    E244514E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-6 (MCO-) - Q4-12 (SNS2)
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


NG
Go to step 10
OK


9.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Reconnect the radio receiver assembly connector.



    E244515E01
  1. Reconnect the map light assembly (telephone microphone assembly) connector.

  1. Turn the ignition switch to ON (ACC).

  1. Connect an oscilloscope to terminals 5 (MCO+) and 6 (MCO-) of the map light assembly (telephone microphone assembly) connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


B
Go to step 10
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

10.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (Click here).

  1. Check if the malfunction recurs.

    Result:
    Result
    Proceed to
    Malfunction does not recur (returns to normal)
    A
    Malfunction recurs
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END