Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B1579    Voice Recognition Microphone Disconnected

for Preparation Click here


DESCRIPTION

w/o Sliding Roof:
  1. The radio and display receiver assembly and amplifier microphone assembly are connected to each other using the microphone connection detection signal lines.
    This DTC is stored when a microphone connection detection signal line is disconnected.
w/ Sliding Roof:
  1. The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
    This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code
DTC Detection Condition
Trouble Area
B1579
Telephone microphone signal is lost.
  1. Amplifier microphone assembly*1
  2. Map light assembly*2
  3. Telephone microphone assembly*2
  4. Radio and display receiver assembly
  5. Harness or connector
  1. *1: w/o Sliding Roof
  2. *2: w/ Sliding Roof

WIRING DIAGRAM


w/o Sliding Roof

E226160E28


w/ Sliding Roof

E226160E31


INSPECTION PROCEDURE

NOTICE:
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

1.CONFIRM MODEL

Result:
Result
Proceed to
w/o Sliding Roof
A
w/ Sliding Roof
B



B
Go to step 5
A


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E237416E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G78-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
  1. Disconnect the radio and display receiver assembly connector.

  1. Disconnect the amplifier microphone assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G78-6 (SNS2) - Q5-4 (SNS2)
    Always
    Below 1 Ω
    G78-19 (MIN-) - Q5-3 (MCO-)
    Always
    Below 1 Ω
    G78-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G78-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT AMPLIFIER MICROPHONE ASSEMBLY


    E244512E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q5-4 (SNS2) - Q5-3 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Microphone Assembly)



NG
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
OK

END 

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E237416E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G78-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the radio and display receiver assembly connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G78-6 (SNS2) - Q4-12 (SNS2)
    Always
    Below 1 Ω
    G78-19 (MIN-) - Q4-6 (MCO-)
    Always
    Below 1 Ω
    G78-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G78-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    E244514E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-12 (SNS2) - Q4-6 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



NG
Go to step 8
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

8.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END