DTC B1579 Voice Recognition Microphone Disconnected |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1579 | Telephone microphone signal is lost. |
|
| w/o Sliding Roof |

| w/ Sliding Roof |

| 1.CONFIRM MODEL |
| Result | Proceed to |
| w/o Sliding Roof | A |
| w/ Sliding Roof | B |
|
| ||||
| A | |
| 2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G78-19 (MIN-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY) |
Disconnect the radio and display receiver assembly connector.
Disconnect the amplifier microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G78-6 (SNS2) - Q5-4 (SNS2) | Always | Below 1 Ω |
| G78-19 (MIN-) - Q5-3 (MCO-) | Always | Below 1 Ω |
| G78-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G78-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT AMPLIFIER MICROPHONE ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q5-4 (SNS2) - Q5-3 (MCO-) | Always | Below 1 Ω |
| *a | Component without harness connected (Amplifier Microphone Assembly) |
|
| ||||
| OK | ||
| ||
| 5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G78-19 (MIN-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the radio and display receiver assembly connector.
Disconnect the map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G78-6 (SNS2) - Q4-12 (SNS2) | Always | Below 1 Ω |
| G78-19 (MIN-) - Q4-6 (MCO-) | Always | Below 1 Ω |
| G78-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G78-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q4-12 (SNS2) - Q4-6 (MCO-) | Always | Below 1 Ω |
| *a | Component without harness connected (Map Light Assembly (Telephone Microphone Assembly)) |
|
| ||||
| OK | ||
| ||
| 8.REPLACE TELEPHONE MICROPHONE ASSEMBLY |
Replace the telephone microphone assembly (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check if the same DTC is output again.
|
| ||||
| OK | ||
| ||