Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1475/75    A/C Inverter Cooling / Heating System Malfunction

for Preparation Click here


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects inverter temperature.
If the temperature exceeds the maximum, the compressor with motor assembly stops compressor operation, and this DTC will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B1475/75
Cooling water temperature in the inverter is outside the specified range (temperature is too high), or there is an open or short to ground in the temperature sensor circuit.
  1. Cooling fan system
  1. Refrigerant volume
  1. Compressor with motor assembly
  2. CAN communication system

INSPECTION PROCEDURE

CAUTION:
  1. Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.
  2. Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

NOTICE:
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the flow chart for the hybrid control system first if any DTCs from those systems are output simultaneously.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Using the Techstream to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Electrical Fan
Electrical fan
OFF or ON
-

OK:
Electrical fan operates smoothly.



NG
GO TO COOLING FAN SYSTEM (Click here)
OK


3.CHECK REFRIGERANT PRESSURE
  1. Install the manifold gauge set .



    E050573
  1. Read the manifold gauge pressure when the following conditions are established.

    1. Prepare the vehicle according to the chart below.
      Item
      Condition
      Vehicle Doors
      All fully open
      Temperature Setting
      MAX COLD
      Blower Speed
      HI
      A/C switch
      ON
      R/F Switch
      RECIRCULATION
      (30 to 35°C (86 to 95°F))

      Standard Pressure:
      Low pressure side:
      150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
      High pressure side:
      1370 to 1570 kPa (14.0 to 16.0 kgf/cm2, 199 to 228 psi)



NG
CHARGE REFRIGERANT
OK


4.READ OUTPUT DTC (DTC B1475/75)
  1. Clear the DTCs (Click here).

  1. Prepare the vehicle according to the table below.
    Item
    Condition
    Engine speed
    Engine idling
    Blower speed
    HI
    A/C switch
    ON
    Temperature setting
    MAX. COLD

  1. Check for DTCs (Click here).

    Result:

    Result
    Proceed to
    DTC B1475/75 is not output (normal)
    A
    DTC B1475/75 is output
    B

NOTICE:
If the engine keeps idling when ambient temperature is high, the compressor may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.



B
REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)
A

SYSTEM IS OK