Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM

DTC    U0122    Lost Communication with Vehicle Dynamics Control Module

DTC    U0123    Lost Communication with Yaw Rate Sensor Module

DTC    U0126    Lost Communication with Steering Angle Sensor Module

DTC    U0140    Lost Communication with Main Body ECU

DTC    U0151    Lost Communication with Airbag ECU

DTC    U0235    Lost Communication with Cruise Control Front Distance Range Sensor

DTC    U0293    Lost Communication with HV ECU

DTC    U1002    Lost Communication with Gateway Module

DTC    U1100    Lost Communication with Seat Belt Control ECU

DTC    U1104    Lost Communication with Driving Support ECU

for Preparation Click here


DESCRIPTION

  1. The driving support ECU uses the millimeter wave radar sensor to detect obstacles in front of the vehicle. Based on this information, the driving support ECU sends pre-collision control operation signals. These DTCs are stored when a communication malfunction occurs between the sensors and ECUs that detect collisions, or between ECUs that perform the pre-collision control.
  1. The driving support ECU sends vehicle speed and vehicle condition information to the millimeter wave radar sensor. The millimeter wave radar sensor then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU. The driving support ECU sends this information to the ECM and performs pre-collision system (DTC U1104).

    DTC No.
    DTC Detection Condition
    Trouble Area
    U0122
    1. When the power switch is on (IG), a communication error between the brake booster with master cylinder (skid control ECU) and the driving support ECU is detected for approx. 1 second.
    2. When the power switch is on (IG), a communication error between the skid control ECU assembly and the seat belt control ECU is detected for approx. 1 second.
    1. Brake booster with master cylinder (skid control ECU)
    2. CAN communication system
    3. Seat belt control ECU
    4. Driving support ECU
    U0123
    When the power switch is on (IG), a communication error between the yaw rate sensor and the driving support ECU is detected for approx. 1 second.
    1. Yaw rate sensor
    2. CAN communication system
    3. Driving support ECU
    U0126
    When the power switch is on (IG), a communication error between the steering sensor and the driving support ECU is detected for approx. 1 second.
    1. Steering angle sensor
    2. CAN communication system
    3. Driving support ECU
    U0140
    While power switch is on (IG), communication stop between main body ECU and seat belt control ECU continues for 1 second or more.
    1. Main body ECU
    2. CAN communication system
    3. Seat belt control ECU
    U0151
    While power switch is on (IG), communication stop between center airbag sensor and seat belt control ECU continues for 1 second or more.
    1. Center airbag sensor
    2. CAN communication system
    3. Seat belt control ECU
    U0235
    When the power switch is on (IG), a communication error between the millimeter wave radar sensor and the driving support ECU is detected for approx. 1 second.
    1. Communication circuit
    2. Millimeter wave radar sensor
    3. Driving support ECU
    U0293
    1. When the power switch is on (IG), a communication error between the power management control ECU and brake booster with master cylinder (skid control ECU) is detected for approx. 1 second.
    2. When the power switch is on (IG), a communication error between the power management control ECU and driving support ECU is detected for approx. 1 second.
    1. Power management control ECU
    2. Brake booster with master cylinder (skid control ECU)
    3. CAN communication system
    4. Driving support ECU
    U1002
    While the power switch is on (IG), communication stop between the lane recognition camera sensor assembly, millimeter wave radar sensor and driving support ECU continues for 1 second or more.
    1. Lane recognition camera sensor assembly
    2. Millimeter wave radar sensor
    3. CAN communication system
    4. Driving support ECU
    U1100
    When the power switch is on (IG), a communication error between the seat belt control ECU and the driving support ECU is detected for approx. 1 second.
    1. Seat belt control ECU
    2. CAN communication system
    3. Driving support ECU
    U1104
    1. When the power switch is on (IG), a communication error between the driving support ECU and the millimeter wave radar sensor is detected for approx. 1 second.
    2. When the power switch is on (IG), a communication error between the driving support ECU and the power management control ECU is detected for approx. 1 second.
    1. Communication circuit
    2. Millimeter wave radar sensor
    3. Driving support ECU
    4. Power management control ECU
    5. CAN communication system

WIRING DIAGRAM


A220566E05


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the millimeter wave radar sensor with a new one, make sure to perform Adjust Millimeter Wave Radar Sensor Assembly (Click here).
  2. Confirm that the connector is securely connected, as a partially connected connector is suspected for the cause of this DTC.

1.READ OUTPUT DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Pre-Collision and Pre-Collision 2 / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC U1104 is output
    A
    DTC U1104 is not output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK CAN COMMUNICATION SYSTEM
  1. Select "CAN Bus Check" from the "System Selection Menu" screen on the Techstream.

  1. Select "Communication Malfunction DTC" from the "CAN Bus Check" screen, and then select "Enter".

    OK:
    CAN communication is normal.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


3.CHECK MILLIMETER WAVE RADAR SENSOR (IGB VOLTAGE)


    E181639E06
  1. Disconnect the millimeter wave radar sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A2-5 (IGB) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor)

  1. Reconnect the millimeter wave radar sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGB CIRCUIT)
OK


4.CHECK MILLIMETER WAVE RADAR SENSOR (SGND CIRCUIT)


    E181639E07
  1. Disconnect the millimeter wave radar sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-2 (SGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor)

  1. Reconnect the millimeter wave radar sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SGND CIRCUIT)
OK


5.REPLACE MILLIMETER WAVE RADAR SENSOR
  1. Replace the millimeter wave radar sensor (Click here).

  1. Adjust the millimeter wave radar sensor (Click here).


NEXT


6.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the cruise control main switch on.

  1. Drive the vehicle at the required speed (27 mph (45 km/h) or higher).

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC U1104 is not output
    A
    DTC U1104 is output
    B



B
REPLACE DRIVING SUPPORT ECU (Click here)
A

END