Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (READY)

for Preparation Click here


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch.

HINT:
  1. When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).
  2. When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.


WIRING DIAGRAM

Refer to "System Diagram" (Click here)

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
  4. Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  6. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  7. If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch. This prevents the hybrid control system from starting while the steering is locked.
  8. After completing repairs, confirm that the problem does not occur.


HINT:

Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Power source mode does not change to ON (READY)
Power Source Control
  1. Stop Light Switch1
  2. Steering Unlock Switch
  3. Power Supply Condition
  4. IG1 Relay Monitor(Inside)
  5. IG2 Relay Monitor(Inside)
  6. IG1 Relay Monitor(Outside)
  7. IG2 Relay Monitor(Outside)
  8. Latch Circuit
  9. Shift P Signal
  10. Starter Request Signal
Entry&Start
  1. S Code Check
  2. L Code Check
  3. Engine Start Request
-

1.CHECK HYBRID CONTROL SYSTEM (READY ON)
  1. Place the electrical key transmitter sub-assembly on the driver seat.

  1. Depress the brake pedal.

  1. Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
Go to step 2
OK

END (HYBRID SYSTEM PERMISSION CONDITIONS WERE NOT SATISFIED) 

2.CHECK AUXILIARY BATTERY
  1. Measure the auxiliary battery voltage with the power switch off.

    Standard voltage:
    11 to 14 V

    HINT:
    1. It may be possible to tell whether the auxiliary battery is discharged by operating the horn.
    2. If the auxiliary battery voltage is less than 11 V, charge or replace it.


NEXT


3.CHECK FOR DTC (ALL)
  1. Using the intelligent tester, confirm the output of DTCs for all systems.

    OK:
    No DTCs are output.

    NOTICE:
    Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



NG
GO TO DTC CHART
OK


4.CHECK WAVE ENVIRONMENT
  1. If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

    HINT:
    Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).


NEXT


5.CHECK POWER SWITCH CONDITION
  1. Get into the vehicle while carrying an electrical key transmitter sub-assembly.

  1. Move the shift lever to P.

  1. With the brake pedal released, check that pressing the power switch causes the power source mode to change.

    Result:
    Result
    Proceed to
    Off → on (ACC) → on (IG) → off
    A
    Power source mode does not change to on (ACC) and on (IG)
    B
    Power source mode changes to on (IG) but not to on (ACC)
    C
    Power source mode changes to on (ACC) but not to on (IG)
    D



B
GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG AND ACC) (Click here)

C
GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG) (Click here)

D
GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (ACC) (Click here)
A


6.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.
    2. When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The hybrid control system cannot be started when the steering unlock signal is off.

    OK:
    The item in the Data List indicates "ON" (the steering is unlocked).



NG
GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING WHEEL) (Click here)
OK


7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch1
    State of brake pedal/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is OFF.
    3. When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.

    OK:
    The item in the Data List changes when the brake pedal is depressed and released.



NG
Go to step 10
OK


8.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    w/o ID Code Box (Immobiliser Code ECU):
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG
    w/ ID Code Box (Immobiliser Code ECU):
    Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)/OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    1. When NG is displayed:
    1. L code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    2. Steering wheel cannot be locked.
    3. Steering wheel cannot be unlocked (the hybrid system cannot be started).

    OK:
    The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.

    HINT:
    Reasons for verification failure:
    1. The steering lock ECU (steering lock actuator assembly) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 13
OK


9.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Start Condition
    Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/ OK or NG
    OK: Hybrid control system start permitted
    NG: Hybrid control system start prohibited
    1. When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and hybrid control system starting possible.
    2. The hybrid control system cannot be started when NG is displayed.

    NOTICE:
    Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.

    OK:
    The display changes in response to the operation of the power switch.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 15
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)


    E248380E19
  1. Disconnect the A65 stop light switch assembly connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A65-1 (B) - A65-3 (GND)
    Power switch off
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A65-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT STOP LIGHT SWITCH ASSEMBLY


    E248381E20
  1. Reconnect the A65 stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A65-2 (OUT) - A65-3 (GND)
    Power switch off, brake pedal not depressed
    Below 1 V
    A65-2 (OUT) - A65-3 (GND)
    Power switch off, brake pedal depressed
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the G77 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A65 stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G77-18 (STP1) - A65-2 (OUT)
    Always
    Below 1 Ω
    G77-18 (STP1) or A65-2 (OUT) - Body ground
    Always
    10 kΩ or higher



    B269097E09
  1. Reconnect the A65 stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G77-18 (STP1) - Body ground
    Brake pedal released
    1 V or less
    Brake pedal depressed
    9 V or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

13.CHECK STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).

  1. Perform the registration procedures (Refer to the Service Bulletin).


NEXT


14.CHECK HYBRID CONTROL SYSTEM (READY ON)
  1. Place the electrical key transmitter sub-assembly on the driver seat.

  1. Depress the brake pedal.

  1. Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE) 

15.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Check
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    1. When NG is displayed:
    1. registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    2. Steering cannot be locked.
    3. Steering cannot be unlocked (the hybrid system cannot be started).

    OK:
    The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.

    HINT:
    Reasons for verification failure:
    1. The ID code box (immobiliser code ECU) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 18
OK


16.CHECK ENGINE IMMOBILISER SYSTEM


    B231391E20
  1. Check the waveform according to the condition(s) in the table below.
    Text in Illustration 
    *a
    Component with harness connected
    (Hybrid Vehicle Control ECU)



    1. Waveform 1


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G81-23 (IMO) - G80-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



    2. Waveform 2


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G81-22 (IMI) - G80-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected

      OK:
      The waveform is displayed as shown in illustration.



NG
Go to step 20
OK


17.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter Request Signal
    Hybrid control system start request signal status/ON or OFF
    ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held
    OFF: After approx. 1 sec. has elapsed, the power switch is released
    1. When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.
    2. When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain amount of time.

    NOTICE:
    Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.

    OK:
    The display changes in response to the operation of the power switch.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) 

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).

  1. Perform the registration procedures (Refer to the Service Bulletin).


NEXT


19.CHECK HYBRID CONTROL SYSTEM (READY ON)
  1. Place the electrical key transmitter sub-assembly on the driver seat.

  1. Depress the brake pedal.

  1. Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

20.CHECK AND REPLACE HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ID CODE BOX (IMMOBILISER CODE ECU))
  1. Disconnect the G81 connector from the hybrid vehicle control ECU.

  1. Disconnect the G49 connector from the ID code box (immobiliser code ECU).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G81-23 (IMO) - G49-3 (EFII)
    Always
    Below 1 Ω
    G81-22 (IMI) - G49-4 (EFIO)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21.REPLACE HYBRID VEHICLE CONTROL ECU
  1. Replace the hybrid vehicle control ECU with a new one (Click here).


NEXT


22.CHECK HYBRID CONTROL SYSTEM (READY ON)
  1. Place the electrical key transmitter sub-assembly on the driver seat.

  1. Depress the brake pedal.

  1. Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (HYBRID VEHICLE CONTROL ECU WAS DEFECTIVE)