Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1800/51 Short in Driver Side Squib Circuit
·

The airbag ECU assembly detects a line short in the driver side squib circuit during the primary check.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver side squib (Horn button assembly)

·

Airbag ECU assembly


Applies to check mode
B1801/51 Open in Driver Side Squib Circuit
·

The airbag ECU assembly detects an open in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver side squib (Horn button assembly)

·

Airbag ECU assembly


Applies to check mode
B1802/51 Short to GND in Driver Side Squib Circuit
·

The airbag ECU assembly detects a short to ground in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver side squib (Horn button assembly)

·

Airbag ECU assembly


Applies to check mode
B1803/51 Short to B+ in Driver Side Squib Circuit
·

The airbag ECU assembly detects a short to B+ in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver side squib (Horn button assembly)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C350251E01
4.625,2.917 6.417,3.479 1.792,0.563 10 false Airbag ECU Assembly 4.625,2.75 6.417,3.313 1.792,0.563 10 false F56 4.698,1.031 6.49,1.594 1.792,0.563 10 false D+ 4.698,1.865 6.49,2.427 1.792,0.563 10 false D- 4.51,0.927 6.302,1.49 1.792,0.563 10 false 5 4.51,1.76 6.302,2.323 1.792,0.563 10 false 6 3.521,0.927 5.313,1.49 1.792,0.563 10 false 1 3.521,1.76 5.313,2.323 1.792,0.563 10 false 2 3.229,0.927 5.021,1.49 1.792,0.563 10 false D+ 3.26,1.771 5.052,2.333 1.792,0.563 10 false D- 2.115,0.927 3.906,1.49 1.792,0.563 10 false D+ 2.146,1.771 3.938,2.333 1.792,0.563 10 false D- 2.406,0.927 4.198,1.49 1.792,0.563 10 false 2 2.406,1.76 4.198,2.323 1.792,0.563 10 false 1 2.708,2.385 4.5,2.948 1.792,0.563 10 false F22 2.708,2.552 3.906,2.99 1.198,0.438 10 false Spiral Cable Sub-assembly 0.698,2.385 2.49,2.948 1.792,0.563 10 false z6*1, z5*2 0.698,2.563 2.219,2.979 1.521,0.417 10 false Driver Side Squib (Horn Button Assembly) 0.167,3.51 2.865,3.802 2.698,0.292 10 false *2: w/ Passenger Airbag ON/OFF Indicator 0.167,3.229 3.146,3.51 2.979,0.281 10 false *1: w/o Passenger Airbag ON/OFF Indicator

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Passenger Airbag ON/OFF Indicator A
w/ Passenger Airbag ON/OFF Indicator B



A

2.CHECK CONNECTORS

B

8.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C241740C01
1.979,0.948 1.979,1.333 false 0.271,0.948 0.271,1.333 false 0.208,1.354 0.49,1.615 0.281,0.26 10 *1 1.031,0.802 1.302,1.146 0.271,0.344 10 *2 2.75,1.135 3.167,1.604 0.417,0.469 10 *3 1.906,1.344 2.188,1.667 0.281,0.323 10 *4 2.365,0.802 2.75,1.177 0.385,0.375 10 A 2.104,0.802 2.385,1.177 0.281,0.375 10 B 1.76,0.802 2.031,0.99 0.271,0.188 10 C 1.5,0.802 1.771,1.083 0.271,0.281 10 D 0.646,0.802 0.854,1.24 0.208,0.438 10 E 0.385,0.802 0.604,1.219 0.219,0.417 10 F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, airbag ECU assembly and spiral cable sub-assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, airbag ECU assembly and spiral cable sub-assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK HORN BUTTON ASSEMBLY

NG

REPLACE WIRE HARNESS

3.CHECK HORN BUTTON ASSEMBLY
a.
C348742C01
0.417,2.167 0.74,2.396 0.323,0.229 1.75,2.24 2,2.24 false 0.313,1.26 0.313,0.677 false 0.25,1.281 0.698,1.708 0.448,0.427 10 false *1 1.146,0.531 1.604,0.885 0.458,0.354 10 false *2 2.74,0.844 3.135,1.438 0.396,0.594 10 false *3 0.333,1.667 0.667,2 0.333,0.333 10 false *a 2.031,2.156 2.427,2.75 0.396,0.594 10 false SST 0.51,2.198 0.906,2.792 0.396,0.594 10 false z6 2.344,0.531 2.74,1.125 0.396,0.594 10 false A 2.177,0.531 2.573,1.125 0.396,0.594 10 false B 1.76,0.531 2.156,1.125 0.396,0.594 10 false C 1.594,0.531 1.99,1.125 0.396,0.594 10 false D 0.75,0.531 1.146,1.125 0.396,0.594 10 false E 0.438,0.531 0.833,1.125 0.396,0.594 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)


Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK DRIVER SIDE SQUIB CIRCUIT
4.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
C347065C03
0.51,2.219 0.823,2.438 0.313,0.219 1.333,2.198 1.063,1.865 false 1.49,2.198 1.771,1.865 false 0.302,1.094 0.302,0.677 false 0.24,1.115 0.635,1.438 0.396,0.323 10 false *1 1.135,0.542 1.49,0.854 0.354,0.313 10 false *2 2.844,0.844 3.281,1.333 0.438,0.49 10 false *3 0.26,1.635 0.677,2.073 0.417,0.438 10 false *a 0.594,2.24 1.01,2.677 0.417,0.438 10 false z6 1.802,1.792 2.219,2.229 0.417,0.438 10 false D+ 0.875,1.792 1.292,2.229 0.417,0.438 10 false D- 2.521,0.542 2.958,1.031 0.438,0.49 10 false A 2.208,0.542 2.646,1.031 0.438,0.49 10 false B 1.76,0.542 2.198,1.031 0.438,0.49 10 false C 1.604,0.542 2.042,1.031 0.438,0.49 10 false D 0.771,0.531 1.208,1.021 0.438,0.49 10 false E 0.448,0.531 0.885,1.021 0.438,0.49 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z6-2 (D+) - Body ground Power switch on (IG) Below 1 V
z6-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - z6-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - Body ground Always 1 MΩ or higher
z6-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - z6-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK DTC
a.
C238229C04
0.427,0.885 0.427,1.281 false 0.365,1.302 0.646,1.646 0.281,0.344 10 *1 1.083,0.729 1.563,1.313 0.479,0.583 10 *2 2.615,1.01 2.948,1.438 0.333,0.427 10 *3 2.302,0.729 2.573,1.125 0.271,0.396 10 A 2.146,0.729 2.448,1.156 0.302,0.427 10 B 1.698,0.729 2,1.188 0.302,0.458 10 C 1.531,0.729 1.885,1.156 0.354,0.427 10 D 0.708,0.729 1.125,1.229 0.417,0.5 10 E 0.552,0.729 0.906,1.26 0.354,0.531 10 F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly


Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK INSTRUMENT PANEL WIRE
a.
C238259C34
1.229,2.208 1.573,2.448 0.344,0.24 0.219,0.688 0.219,0.979 false 2.042,2.479 1.813,2.833 false 2.198,2.469 2.427,2.823 false 2.083,0.542 2.083,0.219 2.083,0.219 1.917,0.219 false 1.302,2.25 1.76,2.615 0.458,0.365 10 false F22 0.344,0.542 0.667,0.917 0.323,0.375 10 false F 0.667,0.542 1.052,1.104 0.385,0.563 10 false E 1.49,0.542 1.698,0.833 0.208,0.292 10 false D 1.813,0.542 2.177,0.958 0.365,0.417 10 false C 2.26,0.542 2.583,0.844 0.323,0.302 10 false B 2.573,0.542 2.854,0.76 0.281,0.219 10 false A 1.052,0.542 1.354,1.01 0.302,0.469 10 false *2 0.146,1.01 0.594,1.396 0.448,0.385 10 false *1 2.885,0.844 3.188,1.188 0.302,0.344 10 false *3 1.031,1.604 1.552,2.104 0.521,0.5 10 false *a 2.417,2.854 2.792,3.104 0.375,0.25 10 false D- 1.75,0.135 2.063,0.406 0.313,0.271 10 false *4 1.719,2.844 2.125,3.125 0.406,0.281 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the instrument panel wire from the spiral cable sub-assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F22-1 (D+) - Body ground Power switch on (IG) Below 1 V
F22-2 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - F22-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - Body ground Always 1 MΩ or higher
F22-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - F22-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

7.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
C347067C02
0.448,2.344 0.76,2.573 0.313,0.229 2.073,1.094 2.073,0.677 false 0.198,1.094 0.198,0.677 false 1.333,2.167 1.156,1.823 false 1.49,2.167 1.677,1.823 false 0.135,1.115 0.5,1.521 0.365,0.406 10 false *1 1.042,0.542 1.427,1.031 0.385,0.49 10 false *2 2.885,0.823 3.24,1.198 0.354,0.375 10 false *3 2,1.115 2.375,1.438 0.375,0.323 10 false *4 0.26,1.625 0.688,1.948 0.427,0.323 10 false *a 2.573,0.542 2.927,0.917 0.354,0.375 10 false A 2.26,0.542 2.615,0.917 0.354,0.375 10 false B 1.813,0.542 2.167,0.917 0.354,0.375 10 false C 1.5,0.542 1.854,0.917 0.354,0.375 10 false D 0.656,0.542 1.01,0.917 0.354,0.375 10 false E 0.344,0.542 0.698,0.917 0.354,0.375 10 false F 0.542,2.375 0.969,2.698 0.427,0.323 10 false z6 1.719,1.75 2.146,2.073 0.427,0.323 10 false D+ 0.969,1.75 1.396,2.073 0.427,0.323 10 false D-
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z6-2 (D+) - Body ground Power switch on (IG) Below 1 V
z6-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - z6-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - Body ground Always 1 MΩ or higher
z6-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-2 (D+) - z6-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

8.CHECK CONNECTORS
a.
C238331C01
1.99,1.083 1.99,1.469 false 0.271,1.083 0.271,1.469 false 0.208,1.49 0.729,1.844 0.521,0.354 10 *1 1.052,0.948 1.563,1.292 0.51,0.344 10 *2 2.75,0.969 3.229,1.292 0.479,0.323 10 *3 1.917,1.49 2.333,1.792 0.417,0.302 10 *4 2.365,0.938 2.74,1.323 0.375,0.385 10 A 2.104,0.938 2.448,1.438 0.344,0.5 10 B 1.76,0.948 2.135,1.229 0.375,0.281 10 C 1.5,0.948 1.948,1.333 0.448,0.385 10 D 0.656,0.948 1.344,1.49 0.688,0.542 10 E 0.396,0.948 1,1.323 0.604,0.375 10 F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK HORN BUTTON ASSEMBLY

NG

REPLACE WIRE HARNESS

9.CHECK HORN BUTTON ASSEMBLY
a.
C348746C01
0.427,2.156 0.74,2.375 0.313,0.219 2,2.25 1.75,2.25 false 1.281,2.396 0.865,2.854 false 0.313,0.76 0.313,1.177 false 0.25,1.198 0.646,1.5 0.396,0.302 10 false *1 1.156,0.625 1.604,1.01 0.448,0.385 10 false *2 2.729,0.615 3.177,0.969 0.448,0.354 10 false *3 0.302,1.677 0.698,2.167 0.396,0.49 10 false *a 0.698,2.781 1.01,2.938 0.313,0.156 10 false *b 2.042,2.167 2.521,2.583 0.479,0.417 10 false SST 0.51,2.188 0.875,2.49 0.365,0.302 10 false z5 2.344,0.615 2.792,0.969 0.448,0.354 10 false A 2.177,0.615 2.625,0.969 0.448,0.354 10 false B 1.76,0.615 2.208,0.969 0.448,0.354 10 false C 1.594,0.615 2.042,0.969 0.448,0.354 10 false D 0.75,0.615 1.198,0.969 0.448,0.354 10 false E 0.438,0.615 0.885,0.969 0.448,0.354 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (light green connector).

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

NG

10.CHECK DRIVER SIDE SQUIB CIRCUIT
10.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
C348747C01
0.469,2.156 0.823,2.396 0.354,0.24 0.271,1.208 0.271,0.875 false 1.25,2.104 1.031,1.823 false 1.375,2.104 1.594,1.833 false 1.313,2.427 1.729,2.833 false 0.208,1.219 0.573,1.521 0.365,0.302 10 false *1 1.104,0.719 1.51,1.198 0.406,0.479 10 false *2 2.76,0.729 3.219,1.219 0.458,0.49 10 false *3 0.302,1.688 0.698,2.021 0.396,0.333 10 false *a 1.771,2.76 2.167,3.083 0.396,0.323 10 false *b 0.583,2.188 0.99,2.667 0.406,0.479 10 false z5 1.635,1.75 2.083,2.135 0.448,0.385 10 false D+ 0.854,1.75 1.302,2.135 0.448,0.385 10 false D- 2.375,0.729 2.833,1.219 0.458,0.49 10 false A 2.063,0.729 2.521,1.219 0.458,0.49 10 false B 1.708,0.729 2.167,1.219 0.458,0.49 10 false C 1.552,0.729 2.01,1.219 0.458,0.49 10 false D 0.698,0.729 1.156,1.219 0.458,0.49 10 false E 0.375,0.729 0.833,1.219 0.458,0.49 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z5-2 (D+) - Body ground Power switch on (IG) Below 1 V
z5-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - Body ground Always 1 MΩ or higher
z5-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC

NG

12.CHECK INSTRUMENT PANEL WIRE
11.CHECK DTC
a.
C238334C01
0.313,1.01 0.313,0.344 0.313,0.344 0.563,0.344 false 0.594,0.26 1.063,0.521 0.469,0.26 10 false *1 0.427,1.01 1.031,1.688 0.604,0.677 10 false F 0.583,1.01 1.021,1.573 0.438,0.563 10 false E 1.51,1.01 1.729,1.385 0.219,0.375 10 false D 1.667,1.01 1.917,1.375 0.25,0.365 10 false C 2.094,1.01 2.49,1.354 0.396,0.344 10 false B 2.25,1.01 2.542,1.292 0.292,0.281 10 false A 1,1.01 1.49,1.656 0.49,0.646 10 false *2 2.667,1.021 2.979,1.365 0.313,0.344 10 false *3
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly


Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

12.CHECK INSTRUMENT PANEL WIRE
a.
C238335C28
0.5,2.427 0.865,2.656 0.365,0.229 0.281,0.948 0.281,1.229 false 1.281,2.604 1.063,2.958 false 1.438,2.594 1.667,2.948 false 1.969,0.823 1.969,0.396 1.969,0.396 1.802,0.396 false 0.573,2.458 0.917,2.844 0.344,0.385 10 false F22 0.396,0.802 0.583,1.208 0.188,0.406 10 false F 0.667,0.802 0.906,1.26 0.24,0.458 10 false E 1.49,0.813 1.813,1.083 0.323,0.271 10 false D 1.75,0.813 2.094,1.271 0.344,0.458 10 false C 2.104,0.813 2.531,1.292 0.427,0.479 10 false B 2.365,0.813 2.854,1.313 0.49,0.5 10 false A 1.042,0.823 1.458,1.156 0.417,0.333 10 false *2 0.208,1.25 0.667,1.594 0.458,0.344 10 false *1 2.74,0.823 3.146,1.26 0.406,0.438 10 false *3 0.344,1.969 0.719,2.313 0.375,0.344 10 false *a 1.646,2.958 2.042,3.167 0.396,0.208 10 false D- 1.646,0.323 1.979,0.604 0.333,0.281 10 false *4 0.969,2.969 1.563,3.219 0.594,0.25 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the instrument panel wire from the spiral cable sub-assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F22-1 (D+) - Body ground Power switch on (IG) Below 1 V
F22-2 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - F22-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - Body ground Always 1 MΩ or higher
F22-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (D+) - F22-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

13.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
C348748C01
0.531,2.188 0.854,2.396 0.323,0.208 0.25,1.125 0.25,0.875 false 1.979,1.125 1.979,0.875 false 0.927,1.833 1.24,2.115 false 1.667,1.833 1.365,2.115 false 1.771,2.729 1.313,2.448 false 0.188,1.146 0.542,1.469 0.354,0.323 10 false *1 1.031,0.729 1.469,1.073 0.438,0.344 10 false *2 2.781,0.729 3.24,1.156 0.458,0.427 10 false *3 1.917,1.146 2.323,1.604 0.406,0.458 10 false *4 0.333,1.698 0.729,2.188 0.396,0.49 10 false *a 1.813,2.656 2.24,2.948 0.427,0.292 10 false *b 0.625,2.208 1.052,2.5 0.427,0.292 10 false z5 1.698,1.75 2.125,2.042 0.427,0.292 10 false D+ 0.75,1.75 1.177,2.042 0.427,0.292 10 false D- 2.385,0.729 2.844,1.156 0.458,0.427 10 false A 2.104,0.729 2.563,1.156 0.458,0.427 10 false B 1.76,0.729 2.219,1.156 0.458,0.427 10 false C 1.479,0.729 1.938,1.156 0.458,0.427 10 false D 0.656,0.729 1.115,1.156 0.458,0.427 10 false E 0.375,0.729 0.833,1.156 0.458,0.427 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z5-2 (D+) - Body ground Power switch on (IG) Below 1 V
z5-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - Body ground Always 1 MΩ or higher
z5-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY