Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 7 seconds or more, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 7 seconds or more.
·

Power window regulator motor assembly (for driver door)

·

Power window regulator motor assembly (for front passenger door)

·

Power window regulator motor assembly (for rear RH door)

·

Power window regulator motor assembly (for rear LH door)

·

Multiplex network master switch assembly

·

Sliding roof ECU (sliding roof drive gear sub-assembly)*1

·

Double lock door control relay assembly*2

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

ECU-B NO. 2 fuse

·

POWER fuse

·

DOOR fuse

·

DOOR R/L fuse

·

DOOR R/R fuse

·

S/ROOF fuse*1

·

DOOR DBL/L fuse*2

·

ECU-DCC NO. 2 fuse*2



*1: w/ Sliding Roof System

*2: w/ Double Locking System


WIRING DIAGRAM

B433580E02
1.448,0.219 4.813,0.417 3.365,0.198 10 false from Auxiliary Battery 0.438,1.24 1.417,1.458 0.979,0.219 10 false ECU-B NO. 2 1.229,0.958 2.208,1.177 0.979,0.219 10 false 11 1.219,1.531 2.198,1.75 0.979,0.219 10 false 12 1.5,1.083 2.479,1.302 0.979,0.219 10 false B 1.5,1.656 2.479,1.875 0.979,0.219 10 false GND 2.333,1.094 3.313,1.313 0.979,0.219 10 false LIN2 2.344,1.625 3.323,1.844 0.979,0.219 10 false LIN1 2.719,0.938 3.698,1.156 0.979,0.219 10 false 16 2.729,1.469 3.708,1.688 0.979,0.219 10 false 17 4.281,0.927 5.26,1.146 0.979,0.219 10 false 9 4.479,1.083 5.458,1.302 0.979,0.219 10 false LIN 5.5,1.083 6.479,1.302 0.979,0.219 10 false B 5.719,0.958 6.698,1.177 0.979,0.219 10 false 2 5.313,1.521 6.292,1.74 0.979,0.219 10 false GND 5.729,1.396 6.708,1.615 0.979,0.219 10 false 1 6.052,1.25 7.031,1.469 0.979,0.219 10 false POWER 1.177,1.979 2.156,2.198 0.979,0.219 10 false J7 4.24,1.854 5.219,2.073 0.979,0.219 10 false J2*1, I2*2 1.177,2.135 2.75,2.646 1.573,0.51 10 false Multiplex Network Master Switch Assembly 4.25,2.031 6.219,2.531 1.969,0.5 10 false Power Window Regulator Motor Assembly (for Driver Door) 0.646,3.25 1.625,3.469 0.979,0.219 10 false DOOR 1.49,3.115 2.469,3.333 0.979,0.219 10 false B 1.49,3.552 2.469,3.771 0.979,0.219 10 false GND 2.396,3.292 3.375,3.51 0.979,0.219 10 false LIN 1.292,2.99 2.271,3.208 0.979,0.219 10 false 2 1.26,3.417 2.24,3.635 0.979,0.219 10 false 1 2.729,3.104 3.708,3.323 0.979,0.219 10 false 9 0.635,3.885 1.615,4.104 0.979,0.219 10 false I2*1, J2*2 0.625,4.052 3.24,4.552 2.615,0.5 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 4.49,3.271 5.469,3.49 0.979,0.219 10 false LIN 5.51,3.094 6.49,3.313 0.979,0.219 10 false B 5.302,3.542 6.281,3.76 0.979,0.219 10 false GND 5.719,2.979 6.698,3.198 0.979,0.219 10 false 2 5.719,3.406 6.698,3.625 0.979,0.219 10 false 1 4.292,3.115 5.271,3.333 0.979,0.219 10 false 9 5.979,3.25 6.958,3.469 0.979,0.219 10 false DOOR R/L 4.125,3.74 5.104,3.958 0.979,0.219 10 false L3 4.115,3.906 6.063,4.448 1.948,0.542 10 false Power Window Regulator Motor Assembly (for Rear LH Door) 0.479,5.219 1.458,5.438 0.979,0.219 10 false DOOR R/R 1.51,5.083 2.49,5.302 0.979,0.219 10 false B 1.5,5.49 2.479,5.708 0.979,0.219 10 false GND 1.292,4.969 2.271,5.188 0.979,0.219 10 false 2 1.292,5.375 2.271,5.594 0.979,0.219 10 false 1 2.385,5.25 3.365,5.469 0.979,0.219 10 false LIN 2.719,5.042 3.698,5.26 0.979,0.219 10 false 9 1.156,5.698 2.135,5.917 0.979,0.219 10 false K2 1.146,5.885 3.094,6.313 1.948,0.427 10 false Power Window Regulator Motor Assembly (for Rear RH Door) 4.5,5.25 5.479,5.469 0.979,0.219 10 false MPX1 4.302,5.073 5.281,5.292 0.979,0.219 10 false 7 5.427,5.083 6.406,5.302 0.979,0.219 10 false +B 5.5,5.479 6.479,5.698 0.979,0.219 10 false E 5.708,4.938 6.688,5.156 0.979,0.219 10 false 1 5.719,5.365 6.698,5.583 0.979,0.219 10 false 2 5.927,5.208 6.906,5.427 0.979,0.219 10 false S/ROOF*4 4.052,5.792 5.031,6.01 0.979,0.219 10 false O10*4 4.063,5.958 5.979,6.385 1.917,0.427 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 4.5,7.448 5.479,7.667 0.979,0.219 10 false LIN 5.438,7.021 6.417,7.24 0.979,0.219 10 false +B 5.229,7.458 6.208,7.677 0.979,0.219 10 false CUPB 5.333,7.865 6.313,8.083 0.979,0.219 10 false GND 4.292,7.26 5.271,7.479 0.979,0.219 10 false 9 5.719,6.885 6.698,7.104 0.979,0.219 10 false 12 5.719,7.344 6.698,7.563 0.979,0.219 10 false 11 5.729,7.729 6.708,7.948 0.979,0.219 10 false 7 5.875,7.156 6.927,7.375 1.052,0.219 10 false DOOR DBL/L*3 5.865,7.604 7.156,7.833 1.292,0.229 10 false ECU-DCC NO. 2*3 3.792,8.083 4.771,8.302 0.979,0.219 10 false F15*3 3.792,8.229 6.635,8.531 2.844,0.302 10 false Double Lock Door Control Relay Assembly 2.729,7.438 3.708,7.656 0.979,0.219 10 false 3D 2.729,7 3.708,7.219 0.979,0.219 10 false 3H 2.74,6.813 3.719,7.031 0.979,0.219 10 false 25 2.74,7.26 3.719,7.479 0.979,0.219 10 false 17 1.708,7.438 2.688,7.656 0.979,0.219 10 false MB 1.729,7.25 2.708,7.469 0.979,0.219 10 false 16 1.323,7.458 2.302,7.677 0.979,0.219 10 false LIN2 1.813,8.01 3.427,8.583 1.615,0.573 10 false Instrument Panel Junction Block Assembly 0.021,8.177 1.667,8.917 1.646,0.74 10 false Main Body ECU (Multiplex Network Body ECU) 0.458,9.458 2.292,9.771 1.833,0.313 10 false : LIN Communication Line 0.167,9.104 2,9.417 1.833,0.313 10 false *1: for LHD 1.146,9.104 2.979,9.417 1.833,0.313 10 false *2: for RHD 2.198,9.104 4.302,9.417 2.104,0.313 10 false *3: w/ Double Locking System 4.354,9.104 6.458,9.417 2.104,0.313 10 false *4: w/ Sliding Roof System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it is necessary to perform initialization. (w/ Sliding Roof System)

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

Before performing the inspection, check that DTC B1206, B1249, B1273, B2321, B2322, B2323 or B2324 is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B426691C01
5.667,1.417 6,1.583 0.333,0.167 5.667,0.167 6,0.333 0.333,0.167 2,1.083 2.333,1.25 0.333,0.167 2.167,2 2.167,1.573 false 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 2.063,1.083 2.375,1.281 0.313,0.198 10 false MB 5.75,1.427 6.063,1.625 0.313,0.198 10 false 3H 5.75,0.177 6.063,0.375 0.313,0.198 10 false 3D 2.052,2.031 2.365,2.229 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - MB-16 (LIN2) Always Below 1 Ω
3D-17 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

for LHD

i.

Disconnect the J2 power window regulator motor assembly (for driver door) connector.


ii.

Disconnect the I2 power window regulator motor assembly (for front passenger door) connector.


iii.

Disconnect the L3 power window regulator motor assembly (for rear LH door) connector.


iv.

Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.


v.

Disconnect the J7 multiplex network master switch assembly connector.


vi.

Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector*


vii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - J7-17 (LIN1) Power switch off Below 1 Ω
3D-17 - O10-7 (MPX1)* Power switch off Below 1 Ω
3H-25 - I2-9 (LIN) Power switch off Below 1 Ω
3H-25 - L3-9 (LIN) Power switch off Below 1 Ω
3H-25 - K2-9 (LIN) Power switch off Below 1 Ω
3H-25 - J2-9 (LIN) Power switch off Below 1 Ω
J7-17 (LIN1) - Body ground Power switch off 10 kΩ or higher
O10-7 (MPX1) - Body ground* Power switch off 10 kΩ or higher
3H-25 or 3D-17 - Body ground Power switch off 10 kΩ or higher
I2-9 (LIN) - Body ground Power switch off 10 kΩ or higher
L3-9 (LIN) - Body ground Power switch off 10 kΩ or higher
K2-9 (LIN) - Body ground Power switch off 10 kΩ or higher
J2-9 (LIN) - Body ground Power switch off 10 kΩ or higher


*: w/ Sliding Roof System




b.

for RHD

i.

Disconnect the I2 power window regulator motor assembly (for driver door) connector.


ii.

Disconnect the J2 power window regulator motor assembly (for front passenger door) connector.


iii.

Disconnect the L3 power window regulator motor assembly (for rear LH door) connector.


iv.

Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.


v.

Disconnect the J7 multiplex network master switch assembly connector.


vi.

Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*1


vii.

Disconnect the F15 double lock door control relay assembly connector.*2


viii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - J7-17 (LIN1) Power switch off Below 1 Ω
3D-17 - O10-7 (MPX1)*1 Power switch off Below 1 Ω
3D-17 - F15-9 (LIN)*2 Power switch off Below 1 Ω
3H-25 - I2-9 (LIN) Power switch off Below 1 Ω
3H-25 - L3-9 (LIN) Power switch off Below 1 Ω
3H-25 - K2-9 (LIN) Power switch off Below 1 Ω
3H-25 - J2-9 (LIN) Power switch off Below 1 Ω
J7-17 (LIN1) - Body ground Power switch off 10 kΩ or higher
O10-7 (MPX1) - Body ground*1 Power switch off 10 kΩ or higher
F15-9 (LIN) - Body ground*2 Power switch off 10 kΩ or higher
3H-25 or 3D-17 - Body ground Power switch off 10 kΩ or higher
I2-9 (LIN) - Body ground Power switch off 10 kΩ or higher
L3-9 (LIN) - Body ground Power switch off 10 kΩ or higher
K2-9 (LIN) - Body ground Power switch off 10 kΩ or higher
J2-9 (LIN) - Body ground Power switch off 10 kΩ or higher


*1: w/ Sliding Roof System

*2: w/ Double Locking System




Result:
Proceed to
OK
NG



OK

3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)
a.

for LHD

i.

Reconnect the 3D and 3H instrument panel junction block assembly connectors.


ii.

Reconnect the J2 power window regulator motor assembly (for driver door) connector.


iii.

Reconnect the I2 power window regulator motor assembly (for front passenger door) connector.


iv.

Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.


v.

Reconnect the J7 multiplex network master switch assembly connector.


vi.

Reconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*


vii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

viii.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

*: w/ Sliding Roof System




b.

for RHD

i.

Reconnect the 3D and 3H instrument panel junction block assembly connectors.


ii.

Reconnect the I2 power window regulator motor assembly (for driver door) connector.


iii.

Reconnect the J2 power window regulator motor assembly (for front passenger door) connector.


iv.

Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.


v.

Reconnect the J7 multiplex network master switch assembly connector.


vi.

Reconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*1


vii.

Reconnect the F15 double lock door control relay assembly connector.*2


viii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

ix.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

*1: w/ Sliding Roof System

*2: w/ Double Locking System




Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Reconnect the L3 power window regulator motor assembly (for rear LH door) connector.


b.

Disconnect the J7 multiplex network master switch assembly connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)
a.

Reconnect the J7 multiplex network master switch assembly connector.


b.

Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

6.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

for LHD

i.

Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.


ii.

Disconnect the J2 power window regulator motor assembly (for driver door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.


ii.

Disconnect the I2 power window regulator motor assembly (for driver door) connector.


iii.

Clear the DTCs.

Click here


iv.

After 10 seconds have elapsed, check if the same DTC is output again.



Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

7.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

7.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)
a.

for LHD

i.

Reconnect the J2 power window regulator motor assembly (for driver door) connector.


ii.

Disconnect the I2 power window regulator motor assembly (for front passenger door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/ Double Locking System without Sliding Roof System) B
DTC B2325 is output (w/o Double Locking System without Sliding Roof System) C
DTC B2325 is not output D



A

8.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

9.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

8.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Reconnect each ECU connector.


b.

Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Double Locking System) A
DTC B2325 is output (w/o Double Locking System) B
DTC B2325 is not output C



A

9.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

9.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Reconnect each ECU connector.


b.

Disconnect the F15 double lock door control relay assembly connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY