88460
1.INSTALL COOLER CONDENSER ASSEMBLY
|
Install in this Direction |
Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.
Add 40 cc (1.35 fl. oz)
ND-OIL 11 or equivalent
88710E
2.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the open ends of the cooler condenser assembly and air conditioner tube and accessory assembly.
| *1 | Air Conditioner Tube and Accessory Assembly |
| *2 | Piping Clamp |
| *a | Groove |
Install a new piping clamp to the air conditioner tube and accessory assembly.
Securely engage the inside step of the piping clamp in the air conditioner tube and accessory assembly groove.
Do not widen the opening of the piping clamp more than the diameter of the air conditioner tube and accessory assembly when installing it.
Do not install the piping clamp with the large diameter section in the wrong direction.
Thoroughly coat 2 new O-rings and the contact surface of the air conditioner tube and accessory assembly with compressor oil.
ND-OIL 11 or equivalent
Install the 2 O-rings to the air conditioner tube and accessory assembly.
Do not let foreign matter adhere to the O-rings or O-ring seals.
Engage the cooler condenser assembly and air conditioner tube and accessory assembly.
| *a | Large Diameter Section of Piping Clamp | - | - |
Engage the parts by holding the pipe, not the piping clamp.
Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.
When inserting, make sure that a click sound is heard.
Check that the air conditioner tube and accessory assembly is securely inserted by pulling it.
88703
3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
Remove the vinyl tape from the discharge hose sub-assembly and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.
ND-OIL 11 or equivalent
Install the O-ring to the discharge hose sub-assembly.
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
16593A
4.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/o Exhaust Heat Recirculation System)
|
Install in this Direction |
Engage the 2 guides to install the No. 2 radiator to support seal to the new No. 1 radiator air guide RH as shown in the illustration.
Install the clip.
|
Install in this Direction |
Engage the 2 claws to install the radiator air guide RH with No. 2 radiator to support seal as shown in the illustration.
16593A
5.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Exhaust Heat Recirculation System)
|
Install in this Direction |
Engage the 2 guides to install the No. 2 radiator to support seal to the new No. 1 radiator air guide RH as shown in the illustration.
Install the clip.
|
Install in this Direction |
Engage the 2 claws to install the radiator air guide RH with No. 2 radiator to support seal as shown in the illustration.
16595A
6.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/o Exhaust Heat Recirculation System)
|
Install in this Direction |
Engage the 2 guides to install the No. 3 radiator to support seal to the new No. 1 radiator air guide LH as shown in the illustration.
Install the clip.
|
Install in this Direction |
Engage the 2 claws to install the radiator air guide LH with No. 3 radiator to support seal as shown in the illustration.
16595A
7.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Exhaust Heat Recirculation System)
|
Install in this Direction |
Engage the 2 guides to install the No. 3 radiator to support seal to the new No. 1 radiator air guide LH as shown in the illustration.
Install the clip.
|
Install in this Direction |
Engage the 2 claws to install the radiator air guide LH with No. 3 radiator to support seal as shown in the illustration.
52021
8.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Exhaust Heat Recirculation System)
for Type A:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
for Type B:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
52611
9.INSTALL FRONT BUMPER ENERGY ABSORBER (w/o Exhaust Heat Recirculation System)
for Type A:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
for Type B:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
52136H
10.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (w/o Exhaust Heat Recirculation System)
for Type B:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
52135J
11.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (w/o Exhaust Heat Recirculation System)
for Type B:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY
16594
12.INSTALL NO. 2 RADIATOR AIR GUIDE
53205
13.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
17752
14.INSTALL INLET NO. 2 AIR CLEANER
53510
15.INSTALL HOOD LOCK ASSEMBLY
81150
16.INSTALL HEADLIGHT ASSEMBLY LH
81110
17.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
18.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
19.WARM UP COMPRESSOR
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
20.INSPECT FOR REFRIGERANT LEAK
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
53301
21.ADJUST HOOD SUB-ASSEMBLY