Home › Engine / Hybrid System › 2ZR-FXE COOLING › RADIATOR
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0233438 RADIATOR A

2ZR-FXE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16533C 1.INSTALL RADIATOR SUPPORT GROMMET

a.

Install the 2 radiator support grommets to the radiator assembly.


Hide 16523A 2.INSTALL RADIATOR SUPPORT CUSHION

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16400 3.INSTALL RADIATOR ASSEMBLY

a.

Engage the 2 guides.


b.

Engage the 2 claws to install the fan shroud assembly to the radiator assembly.

NOTICE:

Do not damage the radiator assembly when installing the fan shroud assembly.



c.

Install the radiator assembly with the fan shroud assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or pipe when installing the radiator assembly with the fan shroud assembly.



d.

Engage the 2 guides.


e.

Engage the 2 claws to install the cooler condenser assembly to the radiator assembly.

NOTICE:

Make sure not to damage the cooler condenser assembly when installing the radiator assembly.



Hide G92A0A 4.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.

Engage the clamp to connect the inlet hybrid water pump hose to the fan shroud assembly.


b.

Engage the 2 claws to install the inverter reserve tank assembly to the fan shroud assembly.


Hide G922C 5.CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

a.

Connect the outlet No. 1 inverter cooling hose and slide the clip to secure it.


Hide 16571C 6.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose and slide the clip to secure it.


Hide 16572D 7.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose and slide the clip to secure it.


Hide G922AA 8.CONNECT INLET NO. 1 INVERTER COOLING HOSE

a.

Connect the inlet No. 1 inverter cooling hose and slide the clip to secure it.


b.

Engage the 3 clamps to connect the wire harness to the fan shroud assembly.


Hide G922H 9.CONNECT INLET HYBRID RADIATOR HOSE

a.

Connect the inlet hybrid radiator hose and slide the clip to secure it.


b.

Engage the clamp to connect the inlet hybrid radiator hose to the fan shroud assembly.


Hide 16264D 10.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose and slide the clip to secure it.


b.

Engage the 4 clamps.


Hide 16261G 11.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose and slide the clip to secure it.


Hide 16595A 12.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/o Exhaust Heat Recirculation System)

Hide 16595A 13.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Exhaust Heat Recirculation System)

Hide 16593A 14.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/o Exhaust Heat Recirculation System)

Hide 16593A 15.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Exhaust Heat Recirculation System)

Hide 52021 16.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 52611 17.INSTALL FRONT BUMPER ENERGY ABSORBER (w/o Exhaust Heat Recirculation System)

Hide 52136H 18.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (w/o Exhaust Heat Recirculation System)

Hide 52135J 19.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (w/o Exhaust Heat Recirculation System)

Hide 16594 20.INSTALL NO. 2 RADIATOR AIR GUIDE

a.

Engage the 5 claws to install a new No. 2 radiator air guide to the radiator assembly.


Hide 53205 21.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Install the upper radiator support sub-assembly with the 5 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

for LHD:

i.

Engage the clamp to connect the hood lock control cable assembly to the upper radiator support sub-assembly.



c.

for RHD:

i.

Engage the clamp to connect the hood lock control cable assembly to the upper radiator support sub-assembly.



d.

w/o Engine Hood Courtesy Switch:

i.

Connect the cooling fan motor RH connector and cooling fan motor LH connector.


ii.

Engage the 7 clamps to connect the wire harness to the upper radiator support sub-assembly and fan shroud assembly.



e.

w/ Engine Hood Courtesy Switch:

i.

Connect the cooling fan motor RH connector and cooling fan motor LH connector.


ii.

Engage the 9 clamps to connect the wire harness to the upper radiator support sub-assembly and fan shroud assembly.



f.

w/o Vehicle Approaching Speaker Assembly:

i.

Connect the 2 horn connectors.



g.

w/ Vehicle Approaching Speaker Assembly:

i.

Connect the 2 horn connectors and vehicle approaching speaker assembly connector.



Hide 17752 22.INSTALL INLET NO. 2 AIR CLEANER

Hide G9040 24.INSTALL INVERTER WATER PUMP ASSEMBLY

Hide 81150 25.INSTALL HEADLIGHT ASSEMBLY LH

Hide 81110 26.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 27.ADD ENGINE COOLANT (for Engine)

Hide 28.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51441 29.INSTALL NO. 1 ENGINE UNDER COVER