Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0230764 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during condenser removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front bumper assembly
·

Ultrasonic sensor detection angle (w/ TOYOTA Parking Assist-sensor System)

·

Ultrasonic sensor detection angle registration (w/ TOYOTA Parking Assist-sensor System)


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Change grille shutter control modes and/or perform initialization (w/ Exhaust Heat Recirculation System) Grille Shutter system (Click here)

PROCEDURE

Hide 81150 2.REMOVE HEADLIGHT ASSEMBLY LH

Hide 81110 3.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17752 5.REMOVE INLET NO. 2 AIR CLEANER

Hide 53205 6.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 16594 7.REMOVE NO. 2 RADIATOR AIR GUIDE

Hide 52136H 8.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (w/o Exhaust Heat Recirculation System)

Hide 52135J 9.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (w/o Exhaust Heat Recirculation System)

Hide 52611 10.REMOVE FRONT BUMPER ENERGY ABSORBER (w/o Exhaust Heat Recirculation System)

Hide 52021 11.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 16595A 12.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/o Exhaust Heat Recirculation System)

a.
E337429C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the No. 1 radiator air guide LH with No. 3 radiator to support seal as shown in the illustration.


b.
E344894C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the 2 guides to remove the No. 3 radiator to support seal from the No. 1 radiator air guide LH as shown in the illustration.


Hide 16595A 13.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/ Exhaust Heat Recirculation System)

a.
E337439C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the No. 1 radiator air guide LH with No. 3 radiator to support seal as shown in the illustration.


b.
E344892C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the 2 guides to remove the No. 3 radiator to support seal from the No. 1 radiator air guide LH as shown in the illustration.


Hide 16593A 14.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/o Exhaust Heat Recirculation System)

a.
E337433C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the No. 1 radiator air guide RH with No. 2 radiator to support seal as shown in the illustration.


b.
E344895C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the 2 guides to remove the No. 2 radiator to support seal from the No. 1 radiator air guide RH as shown in the illustration.


Hide 16593A 15.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/ Exhaust Heat Recirculation System)

a.
E337443C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the No. 1 radiator air guide RH with No. 2 radiator to support seal as shown in the illustration.


b.
E344893C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the 2 guides to remove the No. 2 radiator to support seal from the No. 1 radiator air guide RH as shown in the illustration.


Hide 88703 16.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
E336871

Remove the bolt and disconnect the discharge hose sub-assembly from the cooler condenser assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 17.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

While pressing the end of the air conditioner tube and accessory assembly into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

E336869C02
3.125,3.042 3.75,3.365 3.75,3.365 3.24,2.792 true 4.625,2.688 4.625,2.104 false 5.865,2.688 5.865,2.271 false 4.573,2.75 4.885,2.906 0.313,0.156 10 false *1 5.813,2.74 6.125,2.896 0.313,0.156 10 false *2 3.781,3.302 3.979,3.448 0.198,0.146 10 true *3 4.646,0.813 4.958,0.969 0.313,0.156 10 false *a
*1 Air Conditioner Tube and Accessory Assembly *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Press In - -


NOTICE:
·

If any foreign matter is adhered to the connecting part, brush it off or use compressed air to remove it.

·

Make sure that fragments of the piping clamp do not enter the piping.




b.

Disconnect the air conditioner tube and accessory assembly.

NOTICE:

Clean off any foreign matter near the ends of the air conditioner tube and accessory assembly and cooler condenser assembly.



c.

Remove the 2 O-rings from the air conditioner tube and accessory assembly.

NOTICE:

Wrap the open ends of the separated cooler condenser assembly and air conditioner tube and accessory assembly with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88460 18.REMOVE COOLER CONDENSER ASSEMBLY

a.
E336872C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides and remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.