Home › Engine / Hybrid System › 2ZR-FXE COOLING › RADIATOR
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0233438 RADIATOR A

2ZR-FXE COOLING  RADIATOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front bumper assembly
·

Ultrasonic sensor detection angle (w/ TOYOTA Parking Assist-sensor System)

·

Ultrasonic sensor detection angle registration (w/ TOYOTA Parking Assist-sensor System)


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Change grille shutter control modes and/or perform initialization (w/ Exhaust Heat Recirculation System) Grille Shutter system (Click here)

PROCEDURE

Hide 81150 1.REMOVE HEADLIGHT ASSEMBLY LH

Hide 81110 2.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.DRAIN ENGINE COOLANT (for Engine)

Hide G9040 5.REMOVE INVERTER WATER PUMP ASSEMBLY

Hide 17752 7.REMOVE INLET NO. 2 AIR CLEANER

Hide 53205 8.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.
A378412

w/o Vehicle Approaching Speaker Assembly:

i.

Disconnect the 2 horn connectors.



b.
A375630

w/ Vehicle Approaching Speaker Assembly:

i.

Disconnect the 2 horn connectors and vehicle approaching speaker assembly connector.



c.
A375628

w/o Engine Hood Courtesy Switch:

i.

Disengage the 7 clamps to disconnect the wire harness from the upper radiator support sub-assembly and fan shroud assembly.


ii.

Disconnect the cooling fan motor RH connector and cooling fan motor LH connector.



d.
A375629

w/ Engine Hood Courtesy Switch:

i.

Disengage the 9 clamps to disconnect the wire harness from the upper radiator support sub-assembly and fan shroud assembly.


ii.

Disconnect the cooling fan motor RH connector and cooling fan motor LH connector.



e.
A375631

for LHD:

i.

Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.



f.
A375632

for RHD:

i.

Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.



g.
A375633

Remove the 5 bolts and upper radiator support sub-assembly.


Hide 16594 9.REMOVE NO. 2 RADIATOR AIR GUIDE

A375634

a.

Disengage the 5 claws to remove the No. 2 radiator air guide from the radiator assembly.


Hide 52136H 10.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (w/o Exhaust Heat Recirculation System)

Hide 52135J 11.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (w/o Exhaust Heat Recirculation System)

Hide 52611 12.REMOVE FRONT BUMPER ENERGY ABSORBER (w/o Exhaust Heat Recirculation System)

Hide 52021 13.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 16595A 14.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/o Exhaust Heat Recirculation System)

Hide 16595A 15.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/ Exhaust Heat Recirculation System)

Hide 16593A 16.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/o Exhaust Heat Recirculation System)

Hide 16593A 17.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/ Exhaust Heat Recirculation System)

Hide 16261G 18.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A375635

Slide the clip and disconnect the No. 1 water by-pass hose.


Hide 16264D 19.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A375636

Disengage the 4 clamps.


b.

Slide the clip and disconnect the No. 2 water by-pass hose.


Hide G922H 20.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A375637

Disengage the clamp to disconnect the inlet hybrid radiator hose from the fan shroud assembly.


b.

Slide the clip and disconnect the inlet hybrid radiator hose.


Hide G922AA 21.DISCONNECT INLET NO. 1 INVERTER COOLING HOSE

a.
A375639

Disengage the 3 clamps to disconnect the wire harness from the fan shroud assembly.


b.
A375640

Slide the clip and disconnect the inlet No. 1 inverter cooling hose.


Hide 16572D 22.DISCONNECT NO. 2 RADIATOR HOSE

a.
A375638

Slide the clip and disconnect the No. 2 radiator hose.


Hide 16571C 23.DISCONNECT NO. 1 RADIATOR HOSE

a.
A375641

Slide the clip and disconnect the No. 1 radiator hose.


Hide G922C 24.DISCONNECT OUTLET NO. 1 INVERTER COOLING HOSE

a.
A376616

Slide the clip and disconnect the outlet No. 1 inverter cooling hose.


Hide G92A0A 25.REMOVE INVERTER RESERVE TANK ASSEMBLY

a.
A375644

Disengage the clamp to disconnect the inlet hybrid water pump hose from the fan shroud assembly.


b.

Disengage the 2 claws to remove the inverter reserve tank assembly from the fan shroud assembly.


Hide 16400 26.REMOVE RADIATOR ASSEMBLY

a.
A375642

Disengage the 2 claws.


b.

Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.

NOTICE:

Make sure not to damage the cooler condenser assembly when removing the radiator assembly.



c.

Remove the radiator assembly with the fan shroud assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan shroud assembly.



d.
A375643

Disengage the 2 claws.


e.

Disengage the 2 guides to remove the fan shroud assembly from the radiator assembly.

NOTICE:

Do not damage the radiator assembly when removing the fan shroud assembly.



Hide 16523A 27.REMOVE RADIATOR SUPPORT CUSHION

a.

Remove the 2 radiator support cushions from the radiator assembly.


Hide 16533C 28.REMOVE RADIATOR SUPPORT GROMMET

a.

Remove the 2 radiator support grommets from the radiator assembly.