Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P012800  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)  


DESCRIPTION

The ECM uses the engine coolant temperature sensor, installed to the water outlet, and the No. 2 engine coolant temperature sensor, installed to the radiator pipe assembly, to monitor the operation of the thermostat.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P012800 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Either of the following conditions is met (2 trip detection logic):
·

All of the following conditions are met for 5 seconds or more:

1.

The engine is started cold and then warmed up.

2.

When the estimated engine coolant temperature is 75°C (167°F) or higher, the actual engine coolant temperature is less than 75°C (167°F).


·

All of the following conditions are met for certain period of time:

1.

Cold start.

2.

The engine is running and the engine coolant temperature is increasing.

3.

The temperature detected by the No. 2 engine coolant temperature sensor is higher than the threshold temperature calculated based on the engine coolant temperature sensor value.



·

Water inlet with thermostat sub-assembly (thermostat)

·

Cooling system

·

Engine coolant temperature sensor

·

No. 2 engine coolant temperature sensor

·

Front exhaust pipe assembly

·

ECM


Comes on DTC stored SAE Code: P0128

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Output Judgment by Simulated Engine Coolant Temperature
A121605E53
4.917,2.323 5.302,2.594 false 3.833,2.083 3.719,0.885 3.719,0.885 3.583,0.885 false 4.656,2.615 6.229,3.073 1.573,0.458 10 false Indicated Engine Coolant Temperature Reading 3.104,3.719 5.344,3.927 2.24,0.208 10 false DTC Stored (after 2 Driving Cycles) 2.229,0.792 3.563,1.188 1.333,0.396 10 false Estimated Engine Coolant Temperature 0.708,1.698 1.833,1.896 1.125,0.198 10 false Threshold (75°C) 4.323,1.073 5.219,1.417 0.896,0.344 10 false 5 seconds 1.104,2.74 2.125,3.094 1.021,0.354 10 false Engine Coolant Temperature 2.26,3.354 2.604,3.563 0.344,0.208 10 false Time

The ECM estimates the engine coolant temperature based on the starting temperature, engine load, and engine speed. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction of the thermostat or in the engine cooling system, illuminate the MIL and stores this DTC.


Stuck Open Detection with No. 2 Engine Coolant Temperature Sensor
A375761E01
3.406,3.698 3.698,3.698 3.698,3.698 3.948,2.917 true 5.646,2.125 5.448,2.125 5.448,2.125 5.313,1.781 true 3.625,0.25 3.938,0.25 3.938,0.25 3.698,1.646 true 5.219,0.448 5.021,0.448 5.021,0.448 5.281,1.365 true 0.896,0.844 1.854,1.448 0.958,0.604 10 false Engine Coolant Temperature 5.594,3.323 6.552,3.927 0.958,0.604 10 false Time 4.021,3.75 7.031,4.323 3.01,0.573 10 false DTC Stored (after 2 Driving Cycles) ([A] and [B] is [Judgment timer x 0.7] seconds or more) 2.938,1.104 3.281,1.448 0.344,0.344 10 false [A] 4.625,1.125 4.969,1.469 0.344,0.344 10 false [B] 5.708,2.042 7.125,2.417 1.417,0.375 10 false Threshold Temperature 5.292,0.365 7.042,0.844 1.75,0.479 10 false Engine Coolant Temperature Sensor Value 0.615,0.156 3.594,0.677 2.979,0.521 10 false No. 2 Engine Coolant Temperature Sensor Value (with Stuck Open Thermostat) 0.396,3.604 3.375,4.125 2.979,0.521 10 false No. 2 Engine Coolant Temperature Sensor Value (with Normal Thermostat)

If the temperature detected by the No. 2 engine coolant temperature sensor value is higher than the threshold temperature calculated based on the engine coolant temperature sensor value for (judgment timer x 0.7) seconds or more cumulatively while the engine coolant temperature is increasing, the ECM will determine that the thermostat is stuck open, illuminate the MIL and store this DTC.


MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A231721E26
0.167,1 1.208,1.385 1.042,0.385 10 false 80 km/h [Engine Running] 0.354,1.719 1.229,2.083 0.875,0.365 10 false Power Switch on (IG) 1.771,1.479 2.229,1.792 0.458,0.313 10 false [A] 3.292,1.104 3.865,1.51 0.573,0.406 10 false [B] 4.802,2.938 5.229,3.271 0.427,0.333 10 false [C] 3.031,2.385 4.24,2.833 1.208,0.448 10 false 15 minutes 2.469,0.073 6.875,0.479 4.406,0.406 10 false - Engine coolant temperature when engine started: 56°C or less 2.469,0.417 6.281,0.729 3.813,0.313 10 false - Intake air temperature when engine started: 0 to 35°C 2.469,0.729 7.156,1.115 4.688,0.385 10 false - Heater control set to MAX HOT with fresh air mode selected and A/C off

1.

Turn the power switch off and leave the vehicle for several hours.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) [A].

4.

Turn the GTS on.

5.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Intake Air Temperature.

6.

Check that the value of the Data List item Coolant Temperature is 56°C (133°F) or less and the value of the Data List item Intake Air Temperature is between 0 and 35°C (32 and 95°F).

7.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Set the heater control to MAX HOT with fresh air mode selected and turn the A/C off.

9.

Start the engine.

10.

With the engine running, drive the vehicle at 80 km/h (50 mph) for 15 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

After the value of the Data List item Coolant Temperature stabilizes, check that it is 75°C (167°F) or higher [C].

HINT:

If the value of the Data List item Coolant Temperature is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.



CAUTION / NOTICE / HINT

HINT:
·

When this DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature. If the value of Coolant Temperature is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and their connection condition) between the ECM and the engine coolant temperature sensor first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P012800)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P012800 is output A
DTC P012800 and other DTCs are output B


HINT:

If any DTCs other than P012800 are output, troubleshoot those DTCs first.




A

2.CHECK COOLING SYSTEM

B

2.CHECK COOLING SYSTEM
a.

Check for defects in the cooling system that might cause the system to be excessively cold, such as abnormal cooling fan operation or any modifications.


Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT EXHAUST PIPE ASSEMBLY

NG

REPAIR OR REPLACE COOLING SYSTEM

3.INSPECT FRONT EXHAUST PIPE ASSEMBLY
a.

Inspect the front exhaust pipe assembly (exhaust flow control valve operation).


Result:
Proceed to
OK
NG



OK

4.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

NG

REPLACE FRONT EXHAUST PIPE ASSEMBLY

4.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).

Click hereEngine / Hybrid System>2ZR-FXE COOLING>THERMOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

NG

6.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the No. 2 engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR