Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › EGR COOLER
RM3210E _51 Engine / Hybrid System _047497 2ZR-FXE EMISSION CONTROL _0236606 EGR COOLER A

2ZR-FXE EMISSION CONTROL  EGR COOLER  INSTALLATION  


PROCEDURE

Hide 25601L 1.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY

a.
A379108

Using an E8 "TORX" socket wrench, install the 3 stud bolts to the EGR pipe with cooler sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install a new EGR valve gasket to the EGR valve assembly.


c.

Install the EGR pipe with cooler sub-assembly to the EGR valve assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
A377716C01
1.417,2.979 1.625,3.188 0.208,0.208 10 false *a 2.417,1.865 2.771,2.083 0.354,0.219 10 false *b 2.156,2.021 2.448,2.25 0.292,0.229 10 false *d 1.833,2.417 2.125,2.646 0.292,0.229 10 false *c
*a 7 to 11 mm (0.276 to 0.433 in.)
*b LH
*c Front of the vehicle
*d 180°


Connect the No. 6 water by-pass hose to the EGR pipe with cooler sub-assembly and slide the clip to secure it.


e.

Install a new EGR cooler gasket to the EGR pipe with cooler sub-assembly.


f.

Set the EGR pipe with cooler sub-assembly with the EGR valve assembly to the engine assembly.


g.
A378995C01
0.344,2.135 1.625,3.292 1.281,1.156 1.802,2.135 3.083,3.292 1.281,1.156 0.417,2.177 0.698,2.406 0.281,0.229 10 false *a 1.219,1.771 1.427,1.958 0.208,0.188 10 true *b 0.458,2.771 0.667,3.031 0.208,0.26 10 false *c 1.375,2.583 1.688,2.854 0.313,0.271 10 false *d 1.375,3.01 1.677,3.229 0.302,0.219 10 false *e 1.948,2.781 2.271,3.052 0.323,0.271 10 false *f 2.833,2.604 3.146,2.854 0.313,0.25 10 false *g 2.844,3.01 3.156,3.229 0.313,0.219 10 false *h 0.865,0.656 1.063,0.833 0.198,0.177 10 true *a 1.865,2.188 2.073,2.375 0.208,0.188 10 false *b
*a Stud Bolt (A)
*b Stud Bolt (B)
*c 48 mm (1.890 in.)
*d 26 mm (1.024 in.)
*e 13 mm (0.512 in.)
*f 29 mm (1.142 in.)
*g 14 mm (0.551 in.)
*h 13 mm (0.512 in.)


Using an E8 "TORX" socket wrench, install the stud bolt (A) and stud bolt (B) to the cylinder head sub-assembly and camshaft housing sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


h.
A377713C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Temporarily install the EGR pipe with cooler sub-assembly with the EGR valve assembly to the cylinder head sub-assembly and camshaft housing sub-assembly with the bolt and 2 nuts.


i.
A377711

Temporarily install the EGR pipe with cooler sub-assembly to the exhaust manifold (TWC: Front Catalyst) with 2 new nuts.


j.

Tighten the bolt and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


k.

Tighten the 2 nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


l.

Connect the EGR valve assembly connector.


Hide 16281 2.CONNECT NO. 4 WATER BY-PASS HOSE

a.
A377710C01
2.406,0.792 2.563,0.406 2.563,0.406 2.688,0.406 true 2.313,0.208 2.5,0.396 0.188,0.188 10 true *a 1.615,0.917 1.865,1.167 0.25,0.25 10 false *b 2.75,0.323 2.969,0.604 0.219,0.281 10 false *c 2.135,0.365 2.427,0.594 0.292,0.229 10 false *d
*a Up
*b LH
*c Paint Mark
*d 180°


Connect the No. 4 water by-pass hose to the EGR pipe with cooler sub-assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 87245A 3.CONNECT INLET HEATER WATER HOSE A

a.
A377708C01
2.385,0.708 2.51,0.302 2.51,0.302 2.656,0.302 true 2.292,0.24 2.521,0.49 0.229,0.25 10 false *a 1.74,0.823 2,1.063 0.26,0.24 10 false *b 2.708,0.219 3.083,0.51 0.375,0.292 10 false *c 2.083,0.385 2.344,0.625 0.26,0.24 10 false *d
*a Up
*b LH
*c Paint Mark
*d 120°


Connect the inlet heater water hose A to the EGR pipe with cooler sub-assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 16261 4.CONNECT WATER BY-PASS HOSE

a.
A378992C01
2.354,0.969 2.688,1.146 2.688,1.146 2.833,1.146 true 2.063,0.156 2.375,0.344 0.313,0.188 10 false *a 2.813,0.875 3.104,1.115 0.292,0.24 10 false *b 2.865,1.063 3.156,1.333 0.292,0.271 10 false *c 2.521,0.469 2.823,0.708 0.302,0.24 10 false *d
*a Up
*b LH
*c Paint Mark
*d 180°


Connect the water by-pass hose to the EGR valve assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 16671 6.INSTALL FLOW SHUTTING VALVE (WATER VALVE) (w/ Flow Shutting Valve (Water Valve))

Hide G9200 7.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 9.INSPECT FOR COOLANT LEAK (for Engine)