Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243317 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Front door glass sub-assembly

·

Front door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75720 1.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756C 2.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or moulding excessively.


a.

Using a heat light, heat the front door rear window frame moulding.


b.
B436030C01
1.24,1.26 1.604,1.531 true 1.615,1.906 2.083,2.313 true 1.792,2.438 2.156,2.74 true 1.01,1.125 1.26,1.375 0.25,0.25 10 true *a 2.156,2.25 2.417,2.469 0.26,0.219 10 true *b 2.208,2.635 2.469,2.875 0.26,0.24 10 true *a
*a Double-sided Tape
*b Caulking Sponge


Using a moulding remover, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the front door rear window frame moulding.


Hide 67862 3.DISCONNECT FRONT DOOR WEATHERSTRIP

a.
B436029

Disengage the 2 clips and disconnect the front door weatherstrip.


Hide 68151D 4.REMOVE FRONT DOOR GLASS RUN

Hide 67402F 5.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Hide 68126 6.REMOVE FRONT DOOR FIX WINDOW GLASS

Hide 75754A 7.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

B436032

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Disengage the guide to remove the front door upper window frame moulding from the door frame.


Hide 67914 8.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112 9.REMOVE COWL SIDE TRIM BOARD

Hide 75752C 10.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING

a.

Disconnect each connector.


b.

Disengage each clamp.


c.
B436034

Remove the 5 bolts and front door panel sub-assembly.

NOTICE:

To prevent damage, when removing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.



d.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


e.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



f.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets and front door front window frame moulding.

B436035

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




g.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.