The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
*1: When performing learning using the GTS.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
69284G
3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
74260
4.REMOVE REAR ARMREST ASSEMBLY
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
67604
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
7.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL
67842E
8.REMOVE REAR DOOR SERVICE HOLE COVER
67858B
9.REMOVE REAR DOOR PANEL PROTECTOR
67844A
10.REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
68152C
11.REMOVE REAR DOOR GLASS RUN
67872
12.DISCONNECT REAR DOOR WEATHERSTRIP
67408E
13.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
68124B
14.REMOVE REAR DOOR QUARTER WINDOW GLASS
68104
15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
67674A
16.REMOVE REAR DOOR FRAME GARNISH
75978H
17.REMOVE REAR DOOR LOWER OUTSIDE STRIPE
When removing the rear door lower outside stripe, heat the vehicle body and rear door lower outside stripe using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Lower Outside Stripe and Vehicle Body | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body excessively.
Using a heat light, heat the rear door lower outside stripe and vehicle body.
Pull back on one of the ends of the rear door lower outside stripe to remove it.
When pulling on the rear door lower outside stripe, pull it parallel to the vehicle body.
75988C
18.REMOVE REAR DOOR OUTSIDE STRIPE
When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Outside Stripe and Vehicle Body | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body excessively.
Using a heat light, heat the rear door outside stripe and vehicle body.
Pull back on one of the ends of the rear door outside stripe to remove it.
When pulling on the rear door outside stripe, pull it parallel to the vehicle body.
75989C
19.REMOVE REAR DOOR UPPER OUTSIDE STRIPE
When removing the rear door upper outside stripe, heat the vehicle body and rear door upper outside stripe using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Upper Outside Stripe and Vehicle Body | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body excessively.
Using a heat light, heat the rear door upper outside stripe and vehicle body.
Pull back on one of the ends of the rear door upper outside stripe to remove it.
When pulling on the rear door upper outside stripe, pull it parallel to the vehicle body.