Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM3210E _55 Steering _047523 STEERING GEAR / LINKAGE _0243353 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering gear assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

PROCEDURE

Hide 1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

a.
C345623

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 4.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C345624N01
0.167,0.094 0.323,0.292 0.156,0.198 10 false A 2.146,2.51 2.302,2.708 0.156,0.198 10 false B

Separate the clip (A), disengage the clip (B) from the vehicle body and separate the No. 1 steering column hole cover sub-assembly.

NOTICE:

Do not damage the clips (A) or (B).



Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444C 8.REMOVE REAR MOTOR UNDER COVER LH

Hide 51443E 9.REMOVE REAR MOTOR UNDER COVER RH

Hide 51442 10.REMOVE NO. 2 ENGINE UNDER COVER

Hide 48810 11.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 12.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 13.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.
C345614

Remove the cotter pin and nut.


b.
C345615N02
2.396,1.344 2.219,1.344 2.219,1.344 2.219,1.135 false 2.427,1.281 2.885,1.479 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the tie rod end sub-assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C345616C02
3.427,2.479 3.427,2.094 false 1.198,1.99 1.198,1.719 1.198,1.719 1.344,1.719 false 0.458,0.729 0.865,0.719 true 0.271,0.646 0.458,0.823 0.188,0.177 10 true *a 5.531,2.281 5.844,2.438 0.313,0.156 10 false *b 6.594,0.313 6.906,0.469 0.313,0.156 10 false *c 1.375,1.625 1.688,1.781 0.313,0.156 10 false *d 5.552,2 5.865,2.156 0.313,0.156 10 false *b 0.354,2.073 0.51,2.271 0.156,0.198 10 false A 0.354,2.292 0.51,2.49 0.156,0.198 10 false B 3.323,2.51 3.792,2.719 0.469,0.208 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 14.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 15.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 16.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 17.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 18.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 19.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 45025D 20.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.

Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.


Hide 21.REMOVE STEERING LINK ASSEMBLY

a.
C345626

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 22.SECURE STEERING LINK ASSEMBLY

a.
C348415C01
1.823,1.073 2.333,1.573 2.333,1.573 2.531,1.573 true 0.802,0.5 1.25,0.5 1.25,0.5 1.594,0.885 true 2.583,1.479 2.896,1.635 0.313,0.156 10 false *a 0.5,0.417 0.958,0.615 0.458,0.198 10 false SST
*a Protective Tape


Using SST, secure the steering link assembly in a vise.

SST
09612-00012  

HINT:

Wrap SST with protective tape before use.



Hide 45047 23.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
C165553C04
1.292,1.021 1.292,1.521 1.292,1.521 1.823,1.521 false 1.438,1.021 1.438,1.521 false 1.865,1.458 2.208,1.719 0.344,0.26 10 false *a
*a Matchmark


Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.


b.

Remove the tie rod end sub-assembly LH and lock nut.


Hide 45046 24.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.