Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER
RM3210E _53 Suspension _047519 FRONT SUSPENSION _0237150 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front suspension crossmember sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 4.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444C 8.REMOVE REAR MOTOR UNDER COVER LH

Hide 51443E 9.REMOVE REAR MOTOR UNDER COVER RH

Hide 51442 10.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51108A 11.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

a.

except Rough Road Area Specification Vehicles:

i.
C345328

Remove the 4 bolts and rear side rail reinforcement sub-assembly LH from the front suspension crossmember sub-assembly and vehicle body.



b.

for Rough Road Area Specification Vehicles:

i.
C347362

Remove the 4 bolts and rear side rail reinforcement sub-assembly LH from the front suspension crossmember sub-assembly and vehicle body.



Hide 51107A 12.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 13.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

a.
C345327

Remove the nut and separate front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 14.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 15.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 16.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 18.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 19.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C345331

Remove the 2 bolts and separate 2 wire harness clamp brackets from the front suspension crossmember sub-assembly.


b.
C345329C02
2.021,1.563 2.604,2.135 2.604,2.135 2.729,2.135 true 0.771,0.542 0.896,0.542 0.896,0.542 1.302,0.896 true 2.781,2.073 3.094,2.229 0.313,0.156 10 false *a 0.594,0.469 0.833,0.635 0.24,0.167 10 true *b
*a Transmission Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden block placement location


Using a transmission jack and a wooden block, support the engine assembly with transaxle.

CAUTION:
C345332

·

Support the engine assembly with transaxle until the front suspension crossmember sub-assembly is installed.

·

If the support is removed before the front suspension crossmember sub-assembly is installed, the engine assembly with transaxle may drop.




c.
C345335

Remove the bolt and separate the engine moving control rod.


d.
C345333C02
0.271,2 2.604,2 2.604,2 2.604,1.521 true 0.719,1.729 0.719,2 true 2.938,1.875 3.042,2.313 3.042,2.313 3.146,2.313 true 2.229,2 2.229,1.406 true 1.25,2 1.25,1.677 true 3.188,2.25 3.417,2.417 0.229,0.167 10 false *a 0.104,1.938 0.313,2.135 0.208,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment placement location


Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
C345334

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



e.

Remove the 4 bolts and front suspension crossmember sub-assembly.

C345336


f.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 20.REMOVE STEERING LINK ASSEMBLY

Hide 48829A 21.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 22.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 23.REMOVE FRONT STABILIZER BAR

Hide 48069 24.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C347301

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 25.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 12363A 26.REMOVE ENGINE MOVING CONTROL ROD

a.
C345337

Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.


Hide 51228 27.REMOVE SUSPENSION MEMBER SET PLATE

a.
C345338C01
0.156,0.052 0.406,0.24 0.25,0.188 10 true *a 0.156,1.823 0.469,1.979 0.313,0.156 10 false *b
*a for LH Side
*b for RH Side


Remove the 2 suspension member set plates from the front suspension crossmember sub-assembly.


Hide 28.REMOVE HOLE PLUG

a.
C351205

Remove the 4 hole plugs from the front suspension crossmember sub-assembly.

HINT:

There are 2 different shapes of hole plug.