Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0243554 ELECTRONIC SHIFT LEVER SYSTEM C

P610 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P272C73  Park Pawl Motor Actuator Stuck Closed  


DESCRIPTION

The No. 1 integration relay (P-CON relay) is activated by voltage output from the hybrid vehicle control ECU and supplies power to the shift control actuator assembly (parking lock motor).

If the hybrid vehicle control ECU detects a malfunction of the No. 1 integration relay (P-CON relay), it stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P272C73 Park Pawl Motor Actuator Stuck Closed When the P-CON relay is off, voltage at terminals MUA, MVA or MWA of the hybrid vehicle control ECU is 6 V or more for 0.064 seconds or more.
·

Hybrid vehicle control ECU

·

No. 1 integration relay (P-CON relay)

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY

1.

Turn the power switch on (IG).

2.

With the brake pedal depressed, select neutral (N).

3.

Push the P position switch (transmission shift main switch).



WIRING DIAGRAM

Refer to the wiring diagram for DTC P1C8F14.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>P1C8F14

PROCEDURE

1.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (SHIFT CONTROL ACTUATOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the C2 shift control actuator assembly connector.


b.
C208991C29
0.313,0.917 0.729,1.156 0.417,0.24 1.583,0.917 1.729,0.365 true 0.156,0.104 0.427,0.344 0.271,0.24 10 false *a 1.625,0.208 2.073,0.438 0.448,0.229 10 false BMA 0.417,0.958 0.75,1.208 0.333,0.25 10 false C2
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C2-2 (BMA) - Body ground Power switch off Below 1 V



c.

Reconnect the C2 shift control actuator assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)

NG

3.INSPECT NO. 1 INTEGRATION RELAY (P-CON RELAY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the C2 shift control actuator assembly connector.


c.
C338581C05
1.5,2.385 1.906,2.646 0.406,0.26 1.896,0.219 2.302,0.458 0.406,0.24 0.833,3.688 1.333,3.406 true 1.792,3.99 1.604,3.458 true 1.333,3.177 0.76,3.188 true 0.938,1.271 1,0.594 true 1.125,1.26 1.406,0.615 true 0.781,1.26 0.604,0.667 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.219,2.49 0.531,2.688 0.313,0.198 10 false *b 1.625,2.438 1.938,2.635 0.313,0.198 10 false C2 1.958,0.26 2.271,0.458 0.313,0.198 10 false A50 1.698,4.052 2.292,4.354 0.594,0.302 10 false MWA 0.417,3.115 0.885,3.375 0.469,0.26 10 false MUA 0.49,3.688 0.948,3.938 0.458,0.25 10 false MVA 0.375,0.49 0.844,0.75 0.469,0.26 10 false MUA 0.833,0.427 1.292,0.677 0.458,0.25 10 false MVA 1.26,0.438 1.854,0.74 0.594,0.302 10 false MWA
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Control Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A50-1 (MUA) or C2-1 (MUA) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-2 (MVA) or C2-6 (MVA) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-3 (MWA) or C2-7 (MWA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the C2 shift control actuator assembly connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 1 INTEGRATION RELAY (P-CON RELAY)

OK

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P-CON RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY (P-CON RELAY)

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P-CON RELAY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the 1B No. 1 integration relay connector.


c.
A365587C06
0.115,1 0.5,1.281 0.385,0.281 1.646,1.208 1.813,0.385 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.813,0.198 2.458,0.438 0.646,0.24 10 false BMA 0.188,1.063 0.5,1.26 0.313,0.198 10 false A50
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A50-15 (BMA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the 1B No. 1 integration relay connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P-CON RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P-CON RELAY)
a.

Disconnect the C2 shift control actuator assembly connector.


b.

Disconnect the 1B No. 1 integration relay connector.


c.
C208991C30
0.313,0.917 0.729,1.156 0.417,0.24 1.583,0.927 1.729,0.375 true 0.156,0.104 0.427,0.344 0.271,0.24 10 false *a 1.615,0.219 1.948,0.417 0.333,0.198 10 false BMA 0.427,0.969 0.781,1.198 0.354,0.229 10 false C2
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C2-2 (BMA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the 1B No. 1 integration relay connector.


e.

Reconnect the C2 shift control actuator assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR