Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0243554 ELECTRONIC SHIFT LEVER SYSTEM C

P610 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P1C8F14  Park Pawl Motor Phase U Circuit Short to Ground or Open  P1C9414  Park Pawl Motor Phase V Circuit Short to Ground or Open  P1C9914  Park Pawl Motor Phase W Circuit Short to Ground or Open  


DESCRIPTION

The shift control actuator assembly consists of a parking lock motor and rotation angle sensor. The hybrid vehicle control ECU receives a P position switch signal from the hybrid vehicle control ECU and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The hybrid vehicle control ECU stores these DTCs when it detects a malfunction in the parking lock motor system.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1C8F14 Park Pawl Motor Phase U Circuit Short to Ground or Open With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage at hybrid vehicle control ECU terminal MUA is 6 V or less for 1 second or more.
·

Auxiliary battery

·

Hybrid vehicle control ECU

·

Shift control actuator assembly

·

No. 1 integration relay (P-CON relay)

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored
P1C9414 Park Pawl Motor Phase V Circuit Short to Ground or Open With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage at hybrid vehicle control ECU terminal MVA is 6 V or less for 1 second or more.
·

Auxiliary battery

·

Hybrid vehicle control ECU

·

Shift control actuator assembly

·

No. 1 integration relay (P-CON relay)

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored
P1C9914 Park Pawl Motor Phase W Circuit Short to Ground or Open With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage at hybrid vehicle control ECU terminal MWA is 6 V or less for 1 second or more.
·

Auxiliary battery

·

Hybrid vehicle control ECU

·

Shift control actuator assembly

·

No. 1 integration relay (P-CON relay)

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY

1.

Turn the power switch on (IG).

2.

With the brake pedal depressed, select neutral (N).

3.

Push the P position switch (transmission shift main switch).



WIRING DIAGRAM

C351135E02
5.188,1.698 5.844,1.906 0.656,0.208 10 false P-CON 6.167,1.542 7.01,1.917 0.844,0.375 10 false P CON MTR 4.698,2.167 6.635,2.865 1.938,0.698 10 false No. 1 Integration Relay 5.969,0.781 6.281,0.979 0.313,0.198 10 false 11 4.646,1.281 4.958,1.479 0.313,0.198 10 false 10 4.625,0.792 4.938,0.99 0.313,0.198 10 false 12 5.979,1.281 6.292,1.479 0.313,0.198 10 false 9 4.688,2.01 5,2.208 0.313,0.198 10 false 1B 4.219,1.99 4.438,2.177 0.219,0.188 10 false 2 1.865,2 2.083,2.188 0.219,0.188 10 false 2 1.865,2.344 2.083,2.531 0.219,0.188 10 false 3 1.865,1.625 2.083,1.813 0.219,0.188 10 false 1 2.448,1.646 2.667,1.833 0.219,0.188 10 false 1 2.448,2 2.667,2.188 0.219,0.188 10 false 6 2.448,2.333 2.667,2.521 0.219,0.188 10 false 7 1.854,0.792 2.073,0.979 0.219,0.188 10 false 15 1.469,0.896 1.875,1.188 0.406,0.292 10 false BMA 1.448,1.75 1.833,1.969 0.385,0.219 10 false MUA 1.458,2.104 1.844,2.344 0.385,0.24 10 false MVA 1.417,2.448 1.823,2.677 0.406,0.229 10 false MWA 2.781,1.646 3.167,1.823 0.385,0.177 10 false MUA 2.792,1.99 3.156,2.198 0.365,0.208 10 false MVA 2.792,2.344 3.26,2.615 0.469,0.271 10 false MWA 3.667,2 4.156,2.365 0.49,0.365 10 false BMA 0.365,3.646 0.698,3.823 0.333,0.177 10 false A50 0.354,3.802 2.24,4.219 1.885,0.417 10 false Hybrid Vehicle Control ECU 2.448,3.635 2.781,3.813 0.333,0.177 10 false C2 2.458,3.802 4.885,4.177 2.427,0.375 10 false Shift Control Actuator Assembly 2.771,2.833 4.375,3.292 1.604,0.458 10 false Parking Lock Motor

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove/install the auxiliary battery or disconnect the cable from the negative (-) auxiliary battery terminal before instructed.

·

Do not disconnect the connectors before instructed.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P1C8F14, P1C9414 and P1C9914 are output simultaneously. A
Only DTC P1C8F14, P1C9414 or P1C9914 is output. B


HINT:
·

If DTCs P1C8F14, P1C9414 and P1C9914 are stored at the same time, there may be a malfunction in the parking lock motor (BMA signal) power source circuit.

·

If only DTC P1C8F14, P1C9414 or P1C9914 is stored, there may be a malfunction in the parking lock motor (MUA, MVA or MWA) circuit




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

6.READ VALUE USING GTS (U, V, W VOLTAGE)
2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Read the freeze frame data of P1C8F14, P1C9414 and P1C9914.

Powertrain > Hybrid Control
Tester Display
BATT Voltage for Transmission Control System
Result:
Result Proceed to
BATT Voltage for Transmission Control System is 9 V or more. A
BATT Voltage for Transmission Control System is less than 9 V. B



e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC

NEXT

4.CHARGE AUXILIARY BATTERY
4.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.

Result:
Proceed to
NEXT




NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and select neutral (N).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTC P1C8F14, P1C9414 or P1C9914 is output. A
DTCs P1C8F14, P1C9414 and P1C9914 are not output. B



f.

Turn the power switch off.



A

6.READ VALUE USING GTS (U, V, W VOLTAGE)

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)

6.READ VALUE USING GTS (U, V, W VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / U Phase Parking Lock Motor Terminal Voltage, V Phase Parking Lock Motor Terminal Voltage, W Phase Parking Lock Motor Terminal Voltage.


d.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
W Phase Parking Lock Motor Terminal Voltage
V Phase Parking Lock Motor Terminal Voltage
U Phase Parking Lock Motor Terminal Voltage
50003 397 224,223,222
Result:
Tester Display Measurement Item Range Normal Condition
W Phase Parking Lock Motor Terminal Voltage W phase voltage value 0 to 4.99 V 0 to 3.5 V: On (IG)
V Phase Parking Lock Motor Terminal Voltage V phase voltage value 0 to 4.99 V 0 to 3.5 V: On (IG)
U Phase Parking Lock Motor Terminal Voltage U phase voltage value 0 to 4.99 V 0 to 3.5 V: On (IG)



e.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the C2 shift control actuator assembly connector.


c.
C338581C04
1.5,2.385 1.906,2.646 0.406,0.26 1.896,0.219 2.302,0.458 0.406,0.24 0.833,3.688 1.333,3.406 true 1.792,3.99 1.604,3.458 true 1.333,3.177 0.76,3.188 true 0.938,1.271 1,0.594 true 1.125,1.26 1.406,0.615 true 0.781,1.26 0.604,0.667 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.219,2.49 0.531,2.688 0.313,0.198 10 false *b 1.625,2.438 1.938,2.635 0.313,0.198 10 false C2 1.969,0.271 2.281,0.469 0.313,0.198 10 false A50 1.698,4.052 2.292,4.354 0.594,0.302 10 false MWA 0.417,3.115 0.885,3.375 0.469,0.26 10 false MUA 0.49,3.688 0.948,3.938 0.458,0.25 10 false MVA 0.375,0.49 0.844,0.75 0.469,0.26 10 false MUA 0.833,0.427 1.292,0.677 0.458,0.25 10 false MVA 1.26,0.438 1.854,0.74 0.594,0.302 10 false MWA
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Control Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Display Condition Specified Condition
A50-1 (MUA) - C2-1 (MUA) Power switch off Below 1 Ω
A50-2 (MVA) - C2-6 (MVA) Power switch off Below 1 Ω
A50-3 (MWA) - C2-7 (MWA) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Display Condition Specified Condition
A50-1 (MUA) or C2-1 (MUA) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-2 (MVA) or C2-6 (MVA) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-3 (MWA) or C2-7 (MWA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the C2 shift control actuator assembly connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P-CON RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P-CON RELAY)
a.

Disconnect the C2 shift control actuator assembly connector.


b.

Disconnect the 1B No. 1 integration relay connector.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


c.
C351136C01
1.521,2.417 1.885,2.688 0.365,0.271 1.479,0.313 1.833,0.594 0.354,0.281 0.969,0.781 1.552,1.135 true 1.813,3.573 1.969,3.979 true 0.198,0.188 0.51,0.385 0.313,0.198 10 false *a 0.198,2.479 0.51,2.677 0.313,0.198 10 false *b 1.573,0.385 1.885,0.583 0.313,0.198 10 false C2 1.615,2.479 1.927,2.677 0.313,0.198 10 false 1B 0.646,0.698 1.052,0.948 0.406,0.25 10 false BMA 1.854,4.031 2.521,4.354 0.667,0.323 10 false 1B-10
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)
*b Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C2-2(BMA) - 1B-10 Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C2-2(BMA) or 1B-10 - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the 1B No. 1 integration relay connector.


e.

Reconnect the C2 shift control actuator assembly connector.


Result:
Proceed to
OK
NG



OK

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (PARKING LOCK MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (PARKING LOCK MOTOR)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the 1B No. 1 integration relay connector.


c.
C351137C01
0.135,1.26 0.51,1.531 0.375,0.271 1.5,2.604 1.875,2.875 0.375,0.271 1.135,1.313 1.281,0.698 true 0.854,1.313 0.521,0.729 true 1,1.313 0.906,0.625 true 1.896,4.073 1.792,3.667 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.219,2.635 0.531,2.833 0.313,0.198 10 false *b 0.219,1.323 0.531,1.521 0.313,0.198 10 false A50 0.333,0.573 0.76,0.792 0.427,0.219 10 false MUA 0.75,0.448 1.177,0.667 0.427,0.219 10 false MVA 1.177,0.521 1.604,0.74 0.427,0.219 10 false MWA 1.594,2.667 1.906,2.865 0.313,0.198 10 false 1B 1.74,4.115 2.333,4.438 0.594,0.323 10 false 1B-10
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A50-1 (MUA) - 1B-10 Power switch off Below 50 Ω
A50-2 (MVA) - 1B-10 Power switch off Below 50 Ω
A50-3 (MWA) - 1B-10 Power switch off Below 50 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A50-1 (MUA) - Body ground Power switch off 10 kΩ or higher
A50-2 (MVA) - Body ground Power switch off 10 kΩ or higher
A50-3 (MWA) - Body ground Power switch off 10 kΩ or higher
1B-10 - Body ground Power switch off 10 kΩ or higher



d.

Reconnect the 1B No. 1 integration relay connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 1 INTEGRATION RELAY (P-CON RELAY)

NG

REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

10.INSPECT NO. 1 INTEGRATION RELAY (P-CON RELAY)

OK

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P-CON RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY (P-CON RELAY)

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P-CON RELAY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the 1B No. 1 integration relay connector.


c.
C351137C02
1.51,0.365 1.865,0.667 0.354,0.302 1.521,2.604 1.906,2.875 0.385,0.271 1.688,2.031 1.583,1.49 true 2.323,4.167 2.167,3.667 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 0.24,2.667 0.552,2.865 0.313,0.198 10 false *b 1.583,0.448 1.896,0.646 0.313,0.198 10 false A50 1.625,2.677 1.938,2.875 0.313,0.198 10 false 1B 1.583,2.063 2.083,2.302 0.5,0.24 10 false BMA 2.146,4.219 2.74,4.594 0.594,0.375 10 false 1B-12
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A50-15 (BMA) - 1B-12 Power switch off Below 1 Ω


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A50-15 (BMA) or 1B-12 - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the 1B No. 1 integration relay connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (P-CON RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (P-CON RELAY - BODY GROUND)
a.

Disconnect the 1B No. 1 integration relay connector.


b.
A378538C01
1.521,0.344 1.823,0.604 0.302,0.26 2.042,1.844 1.979,1.458 true 1.583,0.406 1.896,0.604 0.313,0.198 10 false 1B 0.156,0.188 0.469,0.385 0.313,0.198 10 false *a 1.844,1.906 2.281,2.125 0.438,0.219 10 false 1B-11
*a Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1B-11 - Body ground Power switch off Below 1 Ω



c.

Reconnect the 1B No. 1 integration relay connector.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (P-CON RELAY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (P-CON RELAY POWER SOURCE CIRCUIT)
a.

Disconnect the 1B No. 1 integration relay connector.


b.
A378538C02
1.531,0.344 1.875,0.583 0.344,0.24 1.552,1.76 1.615,1.469 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.625,0.396 1.938,0.594 0.313,0.198 10 false 1B 1.354,1.813 1.813,2.042 0.458,0.229 10 false 1B-9
*a Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-9 - Body ground Always 9 to 14 V



c.

Reconnect the 1B No. 1 integration relay connector.


Result:
Proceed to
OK
NG



OK

NG

CHECK AND REPAIR POWER SOURCE CIRCUIT