Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0243554 ELECTRONIC SHIFT LEVER SYSTEM C

P610 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P1C8949  Park Pawl Motor (Initially Drive) Internal Electronic Failure  


DESCRIPTION

The shift control actuator assembly consists of a parking lock motor and rotation angle sensor.

The hybrid vehicle control ECU receives a P position switch signal from the P position switch (transmission shift main switch) and operates the parking lock motor through current control to engage and release the parking lock. The hybrid vehicle control ECU detects the motor rotation angle through signals from the rotation angle sensor and controls the timing of application of current to the coils of the parking lock motor.

If the hybrid vehicle control ECU detects a malfunction in the actuator system, it stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1C8949 Park Pawl Motor (Initially Drive) Internal Electronic Failure Malfunction of the power system, such as when the auxiliary battery is discharged, an open or short occurs in the P-CON relay, shift control actuator assembly (parking lock motor or rotation angle sensor) or wire harness, or an internal malfunction of the shift control actuator assembly (parking lock motor or rotation angle sensor).
·

Hybrid vehicle control ECU

·

Auxiliary battery

·

Shift control actuator assembly

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY

1.

Turn the power switch on (IG).

2.

With the brake pedal depressed, select neutral (N).

3.

Push the P position switch (transmission shift main switch).



WIRING DIAGRAM

C351134E02
2.573,5.177 4.896,5.563 2.323,0.385 10 false Shift Control Actuator Assembly 5.344,1.375 5.906,1.729 0.563,0.354 10 false P-CON 6.271,1.24 7.146,1.698 0.875,0.458 10 false P CON MTR 6.198,0.469 6.51,0.667 0.313,0.198 10 false 11 4.729,0.958 5.042,1.156 0.313,0.198 10 false 10 4.698,0.458 5.01,0.656 0.313,0.198 10 false 12 6.219,0.958 6.531,1.156 0.313,0.198 10 false 9 4.906,1.688 5.219,1.885 0.313,0.198 10 false 1B 4.313,3.719 4.625,3.917 0.313,0.198 10 false 2 2.583,5.01 2.896,5.208 0.313,0.198 10 false C2 2.854,4.604 4.406,4.906 1.552,0.302 10 false Parking Lock Motor 2.802,2.781 4.406,3.177 1.604,0.396 10 false Rotation Angle Sensor 2.542,1.021 2.854,1.219 0.313,0.198 10 false 9 2.542,1.458 2.781,1.625 0.24,0.167 10 false 3 2.552,1.917 2.865,2.115 0.313,0.198 10 false 5 2.563,2.365 2.875,2.563 0.313,0.198 10 false 8 2.885,1.135 3.198,1.333 0.313,0.198 10 false RVC 2.896,1.583 3.208,1.781 0.313,0.198 10 false RA 2.896,2.031 3.208,2.229 0.313,0.198 10 false RB 2.885,2.479 3.198,2.677 0.313,0.198 10 false RE2 1.979,0.354 2.219,0.542 0.24,0.188 10 false 15 1.927,0.563 2.25,0.813 0.323,0.25 10 false A50 1.927,1.125 2.281,1.365 0.354,0.24 10 false A50 1.927,1.563 2.25,1.833 0.323,0.271 10 false A50 1.927,2.021 2.24,2.281 0.313,0.26 10 false A50 1.927,2.469 2.271,2.677 0.344,0.208 10 false A50 1.927,3.375 2.229,3.635 0.302,0.26 10 false A50 1.927,3.813 2.333,4.115 0.406,0.302 10 false A50 1.938,4.271 2.271,4.521 0.333,0.25 10 false A50 0.521,2.656 0.76,2.844 0.24,0.188 10 false F2 0.542,3.083 0.781,3.271 0.24,0.188 10 false F2 0.531,3.531 0.771,3.719 0.24,0.188 10 false F2 0.521,2.469 0.76,2.656 0.24,0.188 10 false 12 0.531,2.906 0.771,3.094 0.24,0.188 10 false 11 0.521,3.344 0.76,3.531 0.24,0.188 10 false 10 1.969,0.917 2.208,1.104 0.24,0.188 10 false 41 1.969,1.375 2.208,1.563 0.24,0.188 10 false 16 1.969,1.833 2.208,2.021 0.24,0.188 10 false 29 1.969,2.281 2.208,2.469 0.24,0.188 10 false 44 2,3.167 2.24,3.354 0.24,0.188 10 false 1 2.01,3.615 2.25,3.802 0.24,0.188 10 false 2 2.01,4.063 2.25,4.25 0.24,0.188 10 false 3 2.552,3.271 2.792,3.458 0.24,0.188 10 false 1 2.542,3.719 2.781,3.906 0.24,0.188 10 false 6 2.552,4.146 2.792,4.333 0.24,0.188 10 false 7 1.5,0.573 1.896,0.833 0.396,0.26 10 false BMA 1.583,1.135 1.896,1.333 0.313,0.198 10 false VC 1.594,1.583 1.906,1.781 0.313,0.198 10 false RA 1.594,2.031 1.906,2.229 0.313,0.198 10 false RB 1.615,2.49 1.927,2.688 0.313,0.198 10 false E2 1.479,3.354 1.875,3.583 0.396,0.229 10 false MUA 1.49,3.823 2,4.052 0.51,0.229 10 false MVA 1.438,4.271 1.896,4.521 0.458,0.25 10 false MWA 0.896,2.667 1.208,2.865 0.313,0.198 10 false E01 0.896,3.083 1.208,3.281 0.313,0.198 10 false E02 0.906,3.521 1.219,3.719 0.313,0.198 10 false E03 3.771,3.729 4.125,3.99 0.354,0.26 10 false BMA 0.542,4.688 2.385,5.198 1.844,0.51 10 false Hybrid Vehicle Control ECU 4.906,1.854 6.823,2.396 1.917,0.542 10 false No. 1 Integration Relay 2.875,3.292 3.271,3.521 0.396,0.229 10 false MUA 2.865,3.75 3.375,3.979 0.51,0.229 10 false MVA 2.865,4.188 3.323,4.438 0.458,0.25 10 false MWA

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove/install the auxiliary battery or disconnect the cable from the negative (-) auxiliary battery terminal before instructed.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Check if DTCs are output.

Result:
Result Proceed to
None of the DTCs in the table below are output. A
Any of the DTCs in the table below are output. B


Priority Relevant DTC
1 P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P06881F ECM/PCM Power Relay Sense Circuit Intermittent
2 P1C8F14 Park Pawl Motor Phase U Circuit Short to Ground or Open
P1C9414 Park Pawl Motor Phase V Circuit Short to Ground or Open
P1C9914 Park Pawl Motor Phase W Circuit Short to Ground or Open

HINT:

Perform troubleshooting for higher priority DTCs first.



e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM, ELECTRONIC SHIFT LEVER SYSTEM)

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Read the freeze frame data of DTC P1C8949.

Powertrain > Hybrid Control
Tester Display
BATT Voltage for Transmission Control System

Result:
Result Proceed to
BATT Voltage for Transmission Control System is 9 V or more. A
BATT Voltage for Transmission Control System is less than 9 V. B


e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Clear DTCs
50002 397

d.

Clear the DTCs.


e.

Disconnect the GTS from the DLC3.


f.

Turn the power switch off.


g.

Leave the vehicle as is for 60 seconds or more.

NOTICE:
·

Do not connect the GTS.

·

Do not depress brake pedal.

·

Do not open/close any of the doors.




Result:
Proceed to
NEXT



NEXT

4.CHARGE AUXILIARY BATTERY
4.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and select neutral (N).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P1C8949 is output. A
DTC P1C8949 is not output. B


f.

Turn the power switch off.



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the C2 shift control actuator assembly connector.


c.
C338581C03
1.5,2.385 1.906,2.646 0.406,0.26 1.479,0.125 1.885,0.365 0.406,0.24 2.052,2 1.969,1.729 true 1.531,3.99 1.74,3.417 true 2.219,4.021 1.938,3.417 true 2.115,3.156 2.708,2.896 true 1.781,3.146 2.271,2.615 true 1.729,1.375 2.219,0.594 true 1.615,2.031 1.76,1.573 true 1.302,2 1.521,1.719 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.219,2.49 0.531,2.688 0.313,0.198 10 false *b 1.615,2.438 1.927,2.635 0.313,0.198 10 false C2 1.552,0.167 1.865,0.365 0.313,0.198 10 false A50 2.115,4.052 2.427,4.25 0.313,0.198 10 false RVC 2.26,0.417 2.573,0.615 0.313,0.198 10 false RA 1.125,2.021 1.438,2.219 0.313,0.198 10 false VC 1.521,2.063 1.833,2.26 0.313,0.198 10 false RB 2,2.031 2.313,2.229 0.313,0.198 10 false E2 2.333,2.479 2.646,2.677 0.313,0.198 10 false RA 2.792,2.813 3.104,3.01 0.313,0.198 10 false RB 1.344,4.042 1.656,4.24 0.313,0.198 10 false RE2
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Control Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A50-41 (VC) - C2-9 (RVC) Power switch off Below 1 Ω
A50-16 (RA) - C2-3 (RA) Power switch off Below 1 Ω
A50-29 (RB) - C2-5 (RB) Power switch off Below 1 Ω
A50-44 (E2) - C2-8 (RE2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A50-41 (VC) or C2-9 (RVC) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-16 (RA) or C2-3 (RA) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-29 (RB) or C2-5 (RB) - Body ground and other terminals Power switch off 10 kΩ or higher
A50-44 (E2) or C2-8 (RE2) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the C2 shift control actuator assembly connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

7.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (ROTATION ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (ROTATION ANGLE SENSOR)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.
A365587C05
0.115,1 0.5,1.281 0.385,0.281 1.417,1.865 1.563,1.563 true 1.781,1.208 1.948,0.385 true 1.771,1.885 1.802,1.427 true 2.198,1.885 2.052,1.542 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.302,1.896 1.615,2.094 0.313,0.198 10 false VC 1.865,0.188 2.177,0.385 0.313,0.198 10 false RA 1.677,1.917 1.99,2.115 0.313,0.198 10 false RB 2.156,1.906 2.469,2.104 0.313,0.198 10 false E2 0.188,1.052 0.5,1.25 0.313,0.198 10 false A50
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-41 (VC) - A50-16 (RA) Power switch off 10 kΩ or higher
A50-41 (VC) - A50-29 (RB) Power switch off 10 kΩ or higher
A50-41 (VC) - A50-44 (E2) Power switch off 590 to 670 Ω
A50-16 (RA) - A50-29 (RB) Power switch off 10 kΩ or higher
A50-16 (RA) - A50-44 (E2) Power switch off 10 kΩ or higher
A50-29 (RB) - A50-44 (E2) Power switch off 10 kΩ or higher



c.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the F2 hybrid vehicle control ECU connector.


b.
A365588C12
0.104,0.99 0.479,1.271 0.375,0.281 2.396,1.104 2.24,0.354 true 2.531,1.083 2.583,0.333 true 2.698,1.083 2.969,0.417 true 0.208,1.052 0.521,1.25 0.313,0.198 10 false F2 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.938,0.229 3.271,0.469 0.333,0.24 10 false E01 2.5,0.146 2.833,0.385 0.333,0.24 10 false E02 2.115,0.167 2.448,0.406 0.333,0.24 10 false E03
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F2-12 (E01) - Body ground Power switch off Below 1 Ω
F2-11 (E02) - Body ground Power switch off Below 1 Ω
F2-10 (E03) - Body ground Power switch off Below 1 Ω



c.

Reconnect the F2 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY
a.

Check that the parking brake is applied.


b.

Disconnect the C2 shift control actuator assembly connector.


c.

Remove the 3 shift control actuator bolts.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>SHIFT CONTROL ACTUATOR>REMOVAL


d.

Slightly pull the shift control actuator assembly from the hybrid vehicle transaxle assembly.


e.

Reconnect the C2 shift control actuator assembly connector.


f.

Release the brake pedal and turn the power switch on (ACC).

NOTICE:

The shift control actuator assembly may operate if the power switch is turned on (IG) or (READY). Do not turn the power switch on (IG) or (READY) during this inspection to prevent the shift control actuator assembly from operating while in contact with the splines.



g.
A376624

Using a screwdriver with its tip wrapped with protective tape or a piece of cloth, rotate the shaft.

NOTICE:
·

During this inspection, make sure to use a screwdriver with its tip wrapped with protective tape or a piece of cloth to prevent the splines of the actuator from being damaged.

·

The shift control actuator assembly cannot be disassembled.



i.

Confirm that the shaft of the shift control actuator assembly rotates smoothly.

OK:

The shaft of the shift control actuator assembly rotates smoothly.



ii.

Measure the voltage according to the value(s) in the table below.

NOTICE:

When measuring the voltage, turn the shift control actuator assembly slowly.


C338777C02
1.354,0.292 1.719,0.552 0.365,0.26 2.177,2.281 1.719,1.51 true 1.74,1.354 1.969,0.594 true 1.365,2.26 1.542,1.625 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 2.906,2.417 3.219,2.615 0.313,0.198 10 false *b 1.958,0.396 2.271,0.594 0.313,0.198 10 false RA 3.063,3.188 3.375,3.385 0.313,0.198 10 false RB 2.135,2.323 2.448,2.521 0.313,0.198 10 false RB 1.271,2.313 1.583,2.51 0.313,0.198 10 false E2 3.042,2.75 3.354,2.948 0.313,0.198 10 false RA 1.417,0.344 1.729,0.542 0.313,0.198 10 false A50
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Output Waveform while Splines of Shift Control Actuator Assembly being Rotated (Example)


Standard Voltage:
Tester Connection Condition Specified Condition
A50-16 (RA) - A50-44 (E2) Power switch on (ACC), shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V
A50-29 (RB) - A50-44 (E2) Power switch on (ACC), shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V




h.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY