Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2439  Headlamp LH Circuit  B243A  Headlamp RH Circuit  


DESCRIPTION

A DTC is stored when the No. 1 headlight ECU sub-assembly receives a light source malfunction signal from its respective headlight unit. The No. 1 headlight ECU sub-assembly LH stores DTC B2439 or B243A.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2439 Headlamp LH Circuit Headlight unit LH light source malfunction
·

Headlight unit assembly LH

·

Headlight unit LH

·

No. 1 headlight ECU sub-assembly LH


-
B243A Headlamp RH Circuit Headlight unit RH light source malfunction
·

Headlight unit assembly RH

·

Headlight unit RH

·

No. 1 headlight ECU sub-assembly RH


-

WIRING DIAGRAM

E333074E16
0.125,3.292 2.406,3.552 2.281,0.26 10 false No. 1 Headlight ECU Sub-assembly 3.49,2.927 5.365,3.229 1.875,0.302 10 false Headlight Unit Assembly 4.604,2.406 6.24,2.635 1.635,0.229 10 false Headlight Unit 5.469,1.49 6.76,1.688 1.292,0.198 10 false Lo/Hi Beam 1.552,1.188 2.844,1.385 1.292,0.198 10 false 4 1.552,1.594 2.844,1.792 1.292,0.198 10 false 5 4.448,1.198 4.604,1.396 0.156,0.198 10 false 5 4.458,1.604 4.615,1.802 0.156,0.198 10 false 6 4.604,2.25 4.76,2.448 0.156,0.198 10 false C 0.125,3.125 0.281,3.323 0.156,0.198 10 false B 0.917,1.302 1.573,1.552 0.656,0.25 10 false LOLED2 0.917,1.698 1.573,1.948 0.656,0.25 10 false LOLED1


CAUTION / NOTICE / HINT

NOTICE:

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch on (IG).


b.

Operate the light control switch to turn on the low beam headlights.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B2439 and B243A are not output.



Result:
Result Proceed to
OK A
NG (DTC B2439 is output) B
NG (DTC B243A is output) C



A

B

3.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

7.INSPECT HEADLIGHT UNIT ASSEMBLY RH
3.INSPECT HEADLIGHT UNIT ASSEMBLY LH
a.

Remove the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit assembly LH from the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Inspect the headlight unit assembly LH.

i.
E337135C34
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.531,2.844 1.406,1.74 true 1.667,2.844 2.177,1.844 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.635,2.448 0.854,2.646 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 1.188,1.573 1.771,1.74 0.583,0.167 10 false LOLED2 2.021,1.667 2.604,1.833 0.583,0.167 10 false LOLED1
*a Component without harness connected
(to Headlight Unit LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.INSPECT HEADLIGHT UNIT LH (LOW BEAM HEADLIGHT)

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

4.INSPECT HEADLIGHT UNIT LH (LOW BEAM HEADLIGHT)
a.

Reconnect the C headlight unit LH connector.


b.
E344744C10
0.438,0.99 0.771,1.198 0.333,0.208 1.313,1.854 1.521,1.531 true 1.885,1.865 1.677,1.531 true 0.854,0.51 1.125,0.677 0.271,0.167 10 false *a 0.573,1.021 0.729,1.219 0.156,0.198 10 false B 0.969,1.875 1.885,2.073 0.917,0.198 10 false LOLED2 1.74,1.875 2.656,2.073 0.917,0.198 10 false LOLED1
*a Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Apply auxiliary battery voltage to the headlight unit LH and check that the light comes on.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → B-4 (LOLED2)
Auxiliary battery negative (-) → B-5 (LOLED1)
Low beam comes on



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Turn the power switch on (IG).


b.

Operate the light control switch to turn on the low beam headlights.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B2439 is not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

7.INSPECT HEADLIGHT UNIT ASSEMBLY RH
a.

Remove the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit assembly RH from the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Inspect the headlight unit assembly RH.

i.
E337135C34
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.531,2.844 1.406,1.74 true 1.667,2.844 2.177,1.844 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.635,2.448 0.854,2.646 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 1.188,1.573 1.771,1.74 0.583,0.167 10 false LOLED2 2.021,1.667 2.604,1.833 0.583,0.167 10 false LOLED1
*a Component without harness connected
(to Headlight Unit RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

8.INSPECT HEADLIGHT UNIT RH (LOW BEAM HEADLIGHT)

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

8.INSPECT HEADLIGHT UNIT RH (LOW BEAM HEADLIGHT)
a.

Reconnect the C headlight unit RH connector.


b.
E344744C10
0.438,0.99 0.771,1.198 0.333,0.208 1.313,1.854 1.521,1.531 true 1.885,1.865 1.677,1.531 true 0.854,0.51 1.125,0.677 0.271,0.167 10 false *a 0.573,1.021 0.729,1.219 0.156,0.198 10 false B 0.969,1.875 1.885,2.073 0.917,0.198 10 false LOLED2 1.74,1.875 2.656,2.073 0.917,0.198 10 false LOLED1
*a Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Apply auxiliary battery voltage to the headlight unit RH and check that the light comes on.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → B-4 (LOLED2)
Auxiliary battery negative (-) → B-5 (LOLED1)
Low beam comes on



Result:
Proceed to
OK
NG



OK

9.CLEAR DTC

NG

9.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Turn the power switch on (IG).


b.

Operate the light control switch to turn on the low beam headlights.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B243A is not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH