The No. 1 headlight ECU sub-assemblies control the daytime running lights.
If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime Running Lights | ON or OFF | - |
| Tester Display |
|---|
| Daytime Running Light |
Daytime running lights illuminate.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LH Side) | B |
| NG (for RH Side) | C |
A
B
C
Disconnect the A26 fog light assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A26-2 (DRL) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A26-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A18 No. 1 headlight ECU sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A18-8 (RLD2) - A26-3 (DRLC) | Always | Below 1 Ω |
| A18-8 (RLD2) or A26-3 (DRLC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fog light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY>REMOVAL
Inspect the fog light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY>INSPECTION
Daytime running light LH operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A25 fog light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-2 (DRL) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A19 No. 1 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A19-8 (RLD2) - A25-3 (DRLC) | Always | Below 1 Ω |
| A19-8 (RLD2) or A25-3 (DRLC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fog light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY>REMOVAL
Inspect the fog light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY>INSPECTION
Daytime running light RH operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG