When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the No. 1 headlight ECU sub-assembly LH and illuminates the clearance lights.
If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Clearance Light | Clearance lights | ON or OFF | - |
| Tester Display |
|---|
| Clearance Light |
Clearance lights illuminate.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LH Side) | B |
| NG (for RH Side) | C |
A
B
C
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Remove the headlight unit assembly LH from the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
| *a | Component without harness connected
(to Headlight Lens LH) |
| *b | Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-2 - B-19 (CLL+) | Always | Below 1 Ω |
| D-1 - B-2 (CLL-) | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the D headlight lens LH connector.
| *a | Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH) |
Apply auxiliary battery voltage to the headlight lens LH and check that the light comes on.
| Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → B-19 (CLL+)
Auxiliary battery negative (-) → B-2 (CLL-) |
Clearance light comes on |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Remove the headlight unit assembly RH from the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
| *a | Component without harness connected
(to Headlight Lens RH) |
| *b | Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-2 - B-19 (CLL+) | Always | Below 1 Ω |
| D-1 - B-2 (CLL-) | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the D headlight lens RH connector.
| *a | Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH) |
Apply auxiliary battery voltage to the headlight lens RH and check that the light comes on.
| Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → B-19 (CLL+)
Auxiliary battery negative (-) → B-2 (CLL-) |
Clearance light comes on |
| Proceed to |
|---|
| OK |
| NG |
OK
NG