Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0244634 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1498/98  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The hybrid vehicle control ECU and compressor with motor assembly communicate via direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information is received.

This DTC is also detected if high-voltage electricity supplied from the inverter with converter assembly to the compressor control circuit is shut off.

This DTC will be stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1498/98 Communication Malfunction (A/C Inverter Local)
·

Error or open in communication line between the hybrid vehicle control ECU and compressor with motor assembly

·

High-voltage power source shut off


·

Harness or connector between compressor with motor assembly and body ground

·

Harness or connector between hybrid vehicle control ECU and compressor with motor assembly, battery state sensor assembly

·

Hybrid vehicle control ECU

·

Compressor with motor assembly

·

Air conditioning wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

CAN communication system

·

Hybrid control system


Memorized

WIRING DIAGRAM

E334616E05
0.958,1.813 1.417,2.01 0.458,0.198 10 false LIN 1.396,4.146 1.854,4.344 0.458,0.198 10 false 2 0.073,0.958 2.521,1.188 2.448,0.229 10 false Air Conditioning Amplifier Assembly 0.802,3.219 1.26,3.417 0.458,0.198 10 false DOUT 0.958,3.771 1.417,3.969 0.458,0.198 10 false IG1 0.885,4.344 1.344,4.542 0.458,0.198 10 false GND 0.969,5.125 1.427,5.323 0.458,0.198 10 false PB 0.979,5.635 1.438,5.833 0.458,0.198 10 false PE 1.344,5.646 1.781,5.823 0.438,0.177 10 false T1 1.344,5.125 1.781,5.302 0.438,0.177 10 false T1 1.302,4.344 1.74,4.521 0.438,0.177 10 false C12 1.302,3.771 1.74,3.948 0.438,0.177 10 false C12 1.302,3.219 1.74,3.396 0.438,0.177 10 false C12 1.25,1.667 1.708,1.865 0.458,0.198 10 false 2 1.385,3.583 1.844,3.781 0.458,0.198 10 false 1 1.385,3.021 1.844,3.219 0.458,0.198 10 false 3 1.385,4.938 1.844,5.135 0.458,0.198 10 false 2 1.385,5.458 1.854,5.656 0.469,0.198 10 false 1 0.146,2.313 0.604,2.51 0.458,0.198 10 false C19 0.146,2.469 2.594,2.698 2.448,0.229 10 false Battery State Sensor Assembly 2.198,3.917 3.271,4.198 1.073,0.281 10 false ECU-IG1 NO. 3 2.604,6.177 4.208,6.417 1.604,0.24 10 false Air Conditioning Wire 0.281,6.417 1.333,6.896 1.052,0.479 10 false Compressor with Motor Assembly 2.219,7.01 4.698,7.344 2.479,0.333 10 false : CAN Communication Line 2.219,7.417 4.156,7.698 1.938,0.281 10 false : LIN Communication Line 5.375,6.927 6.74,7.583 1.365,0.656 10 false Inverter with Converter Assembly 5.375,6.771 5.813,6.948 0.438,0.177 10 false T2 5.438,3.813 7.156,4.302 1.719,0.49 10 false Hybrid Vehicle Control ECU 5.438,3.656 5.875,3.833 0.438,0.177 10 false A50 5.083,5 5.542,5.198 0.458,0.198 10 false 1 5.083,5.521 5.542,5.719 0.458,0.198 10 false 2 5.281,5 5.719,5.177 0.438,0.177 10 false ACPB 5.281,5.521 5.719,5.698 0.438,0.177 10 false ACPE 6.031,3.219 6.469,3.396 0.438,0.177 10 false LIN3 5.833,3.063 6.292,3.26 0.458,0.198 10 false 8 3.76,3.792 5.75,3.99 1.99,0.198 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check if hybrid control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
DTC P058A01 and P162B87 are output A
Both DTC P058A01 and P162B87 are not output B



A

3.CHECK FOR DTC

B

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
3.CHECK FOR DTC
a.

Disconnect the C19 battery state sensor assembly connector.


b.

Check if air conditioning system DTCs are output.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1498/98 is output A
DTC B1498/98 is not output B



A

4.CHECK FOR DTC

B

4.CHECK FOR DTC
a.

Reconnect the C19 battery state sensor assembly connector.


b.

Disconnect the C12 compressor with motor assembly connector.


c.

Check if hybrid control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P058A01 and P162B87 are output A
Both DTC P058A01 and P162B87 are not output B



A

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY, BATTERY STATE SENSOR ASSEMBLY)

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY, BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the C19 battery state sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-8 (LIN3) - C12-3 (DOUT) Always Below 1 Ω
A50-8 (LIN3) - C19-2 (LIN) Always Below 1 Ω
A50-8 (LIN3) or C12-3 (DOUT) - Body ground Always 10 kΩ or higher
A50-8 (LIN3) or C19-2 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the C12 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C12-1 (IG1) - C12-2 (GND) Power switch on (IG) 11 to 14 V
C12-1 (IG1) - C12-2 (GND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-8 (LIN3) - C12-3 (DOUT) Always Below 1 Ω
A50-8 (LIN3) or C12-3 (DOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT AIR CONDITIONING WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the T1 and T2 air conditioning wire connectors.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (PB) - T2-1 (ACPB) Always Below 1 Ω
T1-2 (PB) or T2-1 (ACPB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT AIR CONDITIONING WIRE

NG

11.INSPECT AIR CONDITIONING WIRE
10.INSPECT AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-1 (PE) - T2-2 (ACPE) Always Below 1 Ω
T1-1 (PE) or T2-2 (ACPE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

11.INSPECT AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (PB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG