Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0230752 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during compressor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



PROCEDURE

Hide 3.CHECK TERMINAL VOLTAGE

a.

Remove the windshield wiper motor and link.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


b.

for LHD:

i.

Remove the No. 1 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL



c.

for RHD:

i.

Remove the No. 2 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL



d.

Remove the water guard plate LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


e.

Remove the cowl body mounting reinforcement LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


f.

Remove the outer cowl top panel sub-assembly.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


g.

Remove the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL





k.

Install the connector cover assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



m.

Install the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION


n.

Install the outer cowl top panel sub-assembly.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


o.

Install the cowl body mounting reinforcement LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


p.

Install the water guard plate LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


q.

for LHD:

i.

Install the No. 1 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION



r.

for RHD:

i.

Install the No. 2 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION



s.

Install the windshield wiper motor and link.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53289A 5.REMOVE RADIATOR SUPPORT OPENING COVER

Hide 17752 6.REMOVE INLET NO. 2 AIR CLEANER

Hide 17705 7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 8.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17771A 10.REMOVE AIR CLEANER BRACKET

Hide 17751 11.REMOVE INLET NO. 1 AIR CLEANER

Hide 88703 12.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
E336861

Remove the bolt and disconnect the discharge hose sub-assembly from the compressor with motor assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88704 13.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E336862

Remove the bolt and disconnect the suction hose sub-assembly from the compressor with motor assembly.


b.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88370 14.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E336863C02
1.208,0.76 1.667,1.031 true 1.708,0.948 1.906,1.125 0.198,0.177 10 true *a
*a Bracket


Remove the bolt and disconnect the bracket.


b.
E336866C02
1.26,0.563 1.51,0.292 true 2.469,2.146 2.719,1.875 true 2.5,2.646 2.781,2.979 true 2.781,1.813 3.094,1.969 0.313,0.156 10 false *a 2.833,2.927 3.146,3.083 0.313,0.156 10 false *b 1.531,0.219 1.844,0.375 0.313,0.156 10 false *c
*a Connector (A)
*b Connector (B)
*c Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.

Disconnect the connector (B).


d.
E336864

Remove the 3 bolts and compressor with motor assembly.