Home › Brake › BRAKE (REAR) › REAR BRAKE
RM3210E _54 Brake _047537 BRAKE (REAR) _0244653 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 46441 5.LOOSEN NO. 1 WIRE ADJUSTING NUT

Hide 47658B 6.REMOVE PARKING BRAKE LEVER PROTECTOR

Hide 46430 7.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C345058

Remove the nut and separate the No. 3 parking brake cable assembly from the rear trailing arm assembly.


b.
C345967

Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


c.
C345968C02
1.896,3 2.417,3 false 1.875,2.167 2.188,2.167 2.188,2.167 2.354,2.354 false 1.698,2.094 2.01,2.25 0.313,0.156 10 false *a 1.729,2.927 2.042,3.083 0.313,0.156 10 false *1
*1 Rear Disc Brake Cylinder Assembly
*a Clip


Disengage the clip and separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


Hide 47319F 8.DISCONNECT REAR FLEXIBLE HOSE

a.
C345969

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 47850 9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C349631C01
1.5,0.667 1.813,0.823 0.313,0.156 10 false *a 0.354,1.917 0.667,2.073 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake pad guide pins and remove the 2 bolts and rear disc brake cylinder assembly from the disc brake cylinder mounting.


Hide 10.REMOVE ANTI SQUEAL SPRING

a.
C349632

Remove the 2 anti-squeal springs from the rear disc brake pads.


Hide 04466 11.REMOVE REAR DISC BRAKE PAD KIT

a.
C349633

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 12.REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.

Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.


Hide 13.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C349634

Remove the 2 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47835 14.REMOVE REAR DISC BRAKE PAD GUIDE PIN

a.
C363537

Remove the 2 rear disc brake pad guide pins from the rear disc brake cylinder mounting.


b.
C336764C02
1.979,1.25 2.271,0.969 2.271,0.969 2.573,0.969 false 2.615,0.875 2.927,1.031 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from each rear disc brake pad guide pin.

NOTICE:

Do not damage the rear disc brake pad guide pins.



Hide 47775D 15.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C349636

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 47722A 16.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C349637

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.


Hide 42431 17.REMOVE REAR DISC

a.
C349638C01
1.823,1.01 2.698,0.979 2.698,0.979 1.802,0.948 true 2.75,0.906 3.063,1.063 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and the rear axle hub and bearing assembly.


b.

Remove the rear disc.