Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0244714 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Windshield glass sub-assembly Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Lane departure alert system (w/ Steering Control)

·

Pre-crash safety system

·

Forward recognition camera system

·

Automatic high beam system


(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD MOULDING OUTSIDE LH

Hide 75533 2.REMOVE WINDSHIELD MOULDING OUTSIDE RH

HINT:

Use the same procedure as for the LH side.


Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

Hide 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55754F 6.REMOVE COWL WATER EXTRACT SHIELD LH

Hide 55753D 7.REMOVE COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.


Hide 55781E 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 88620E 10.REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Hide 89941 11.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 8646C 12.REMOVE FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)

Hide 81260A 13.REMOVE MAP LIGHT ASSEMBLY

Hide 62312B 14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

Hide 62311B 16.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62211 17.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 74610A 18.REMOVE ASSIST GRIP ASSEMBLY

Hide 74325 19.REMOVE VISOR BRACKET COVER (for LH Side)

Hide 74320 20.REMOVE VISOR ASSEMBLY LH

Hide 74348C 21.REMOVE VISOR HOLDER LH

Hide 74325 22.REMOVE VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74310 23.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348B 24.REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 25.SEPARATE ROOF HEADLINING ASSEMBLY

a.

Slightly lower the front section of the roof headlining assembly so that the windshield glass sub-assembly can be removed.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.


HINT:

It is not necessary to completely remove the roof headlining assembly.



Hide 86050 26.REMOVE TELEVISION ANTENNA ASSEMBLY (w/ Television Antenna)

Hide 863C0 27.REMOVE DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

Hide 56111 28.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.
B435083C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.


b.
B431533C02
2.396,1.01 2.854,1.229 false 2.229,1.281 2.677,1.708 false 1.385,0.25 1.688,0.542 false 1.177,0.177 1.49,0.333 0.313,0.156 10 false *1 2.927,1.167 3.24,1.323 0.313,0.156 10 false *2 2.74,1.635 3.052,1.792 0.313,0.156 10 false *a
*1 Windshield Glass
*2 Windshield Outside Moulding
*a Cut


Using a knife, cut off the windshield outside moulding as shown in the illustration.


c.
B435084C01
1.375,1.688 1.375,1.104 1.375,1.104 1.635,1.104 true 1.385,1.385 1.635,1.385 true 1.323,1.698 1.635,1.854 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



d.
B435086C01
1.167,0.365 1.729,0.74 1.729,0.74 2.333,0.365 false 0.927,1.667 1.031,1.958 false 1.292,1.625 1.573,1.302 false 1.688,0.771 2,0.927 0.313,0.156 10 false *1 1.125,1.896 1.438,2.052 0.313,0.156 10 false *a 1.635,1.219 1.948,1.375 0.313,0.156 10 false *2
*1 Windshield Glass Stopper
*2 Front Window Inner Center Moulding
*a Piano Wire


Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.

·

Do not damage the front window inner center moulding.




g.

Disengage the windshield glass stoppers.

B435087C01
1.531,0.969 1.729,0.74 false 5.01,0.469 5.333,0.688 false 5.583,0.875 5.583,1 false 5.448,0.823 5.448,1 false 5.313,0.896 5.313,1 5.313,1 5.729,1 false 1,0.146 1.323,0.427 0.323,0.281 12 false *A 4.521,0.156 4.865,0.448 0.344,0.292 12 false *B 1.344,0.906 1.656,1.063 0.313,0.156 10 false *1 4.802,0.385 5.115,0.542 0.313,0.156 10 false *2 5.792,0.896 6.104,1.052 0.313,0.156 10 false *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting the adhesive.

·

To prevent the windshield glass sub-assembly from falling when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.



HINT:

Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.



h.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 29.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B435088C01
0.094,0.073 0.417,0.427 0.323,0.354 12 false *A
*A Back Side


Using a scraper, remove the window glass adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.





Hide 75533G 30.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B435089C01
0.146,0.094 0.448,0.406 0.302,0.313 12 false *A
*A Back Side


Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 31.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B435090C01
0.125,0.073 0.417,0.354 0.292,0.281 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 32.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B435091C01
0.146,0.083 0.479,0.385 0.333,0.302 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 33.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B435092

Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56153C 34.REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B435166C01
1.917,2.406 1.917,2.302 false 1.667,2.385 1.667,2.302 1.667,2.302 2.167,2.302 false 0.125,0.083 0.417,0.396 0.292,0.313 12 false *A 2.25,2.219 2.563,2.417 0.313,0.198 10 false *a
*A Back Side
*a Matchmark


Place matchmarks on the windshield glass at the locations indicated in the illustration.


b.

Using a scraper, remove the front window inner center moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the front window inner center moulding with a new one.




Hide 35.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 36.CLEAN VEHICLE BODY

a.

Clean and shape the contact surface of the vehicle body.

i.
B431546C02
0.563,0.458 1,0.719 false 0.385,0.385 0.698,0.542 0.313,0.156 10 false *a 1.625,0.906 1.781,1.104 0.156,0.198 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surface of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.