Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244738 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48760B 1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

a.

Secure the rear suspension support assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the rear suspension support assembly to the rear shock absorber assembly.


c.

Apply a few drops of adhesive to the threads of a new rear support to rear shock absorber nut.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
C345077C02
2.375,1.135 2.552,0.583 2.552,0.583 2.802,0.583 false 2.406,1.906 2.719,2.063 0.313,0.156 10 false *a 2.833,0.531 3.292,0.729 0.458,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and tighten the rear support to rear shock absorber nut.

SST
09729-97202  

Torque:
Specified tightening torque : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Securely insert the 6 mm hexagon socket wrench into the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the rear support to rear shock absorber nut.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

20 N*m (204 kgf*cm, 15 ft.*lbf)




Hide 48554A 2.INSTALL REAR SHOCK ABSORBER CAP

a.

Install the rear shock absorber cap to the rear shock absorber assembly.


Hide 48540 3.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C347353C01
0.833,0.563 1.052,0.563 1.052,0.563 1.323,0.823 true 0.615,0.5 0.833,0.688 0.219,0.188 10 true *1
*1 Rear Axle Carrier Pin


Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 4.STABILIZE SUSPENSION

a.
C345096C02
1.469,1.865 2.125,1.865 false 0.573,2.198 0.875,2.198 false 2.156,1.792 2.469,1.948 0.313,0.156 10 false *a 0.406,2.115 0.719,2.271 0.313,0.156 10 false *b 0.063,1.479 0.271,1.677 0.208,0.198 10 true A
*a Wooden Block
*b Jack
V100155

Wooden Block Placement Location


Using a jack and a wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.

Standard Length (A):

13 mm (0.512 in.)


CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




Hide 48790 5.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Temporarily install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 48540 6.CONNECT REAR SHOCK ABSORBER ASSEMBLY

a.
C345076N02
0.979,1.01 1.135,1.208 0.156,0.198 10 true A 2.438,0.677 2.594,0.875 0.156,0.198 10 true B

Connect the rear shock absorber assembly to the vehicle with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Temporarily tighten bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 48540 7.INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C347355C02
0.958,0.615 1.042,0.229 1.042,0.229 1.271,0.229 true 0.51,0.438 0.448,0.208 0.448,0.208 0.333,0.208 true 2.188,0.448 2.5,0.604 0.313,0.156 10 true *a 1.313,0.156 1.625,0.313 0.313,0.156 10 false *b 2.906,1.635 3.219,1.792 0.313,0.156 10 true *c 0.948,1.844 1.26,2 0.313,0.156 10 true *d 0.125,0.125 0.333,0.302 0.208,0.177 10 true *1
*1 Rear Axle Carrier Pin
*a Torque Wrench Fulcrum Length
*b Ball Joint Lock Nut Wrench
*c Turn
*d Hold


Using a ball joint lock nut wrench fully tighten the rear shock absorber assembly with the nut.

Torque:
Specified tightening torque : 125 N*m (1275 kgf*cm, 92 ft.*lbf)

NOTICE:

Hold the rear axle carrier pin while rotating the nut.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150.25 mm (5.92 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):

91 N*m (928 kgf*cm, 67 ft.*lbf)




Hide 48790 8.INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48840A 9.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 89408C 10.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 57628C 11.INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 12.INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 13.INSTALL REAR WHEEL

Hide 14.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 15.PERFORM INITIALIZATION

Intelligent clearance sonar system
Simple intelligent parking assist system
(Click here)
Parking assist monitor system (Click here)
Automatic headlight beam level control system (Click here)