Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244742 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48727 1.INSTALL REAR SUSPENSION ARM BRACKET

a.
C345103

Temporarily install the rear suspension arm bracket to the rear trailing arm assembly with the bolt and nut.

NOTICE:
·

Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

·

Insert the bolt from the inside of the vehicle.




b.
C345104C02
1.542,1.01 1.583,0.698 1.583,0.698 1.833,0.698 false 2.375,3.167 2.427,3.396 2.427,3.396 2.677,3.396 false 3.063,1.229 3.25,1.438 0.188,0.208 10 false A 1.865,0.615 2.177,0.771 0.313,0.156 10 false *a 2.719,3.333 3.031,3.49 0.313,0.156 10 false *b
*a Upper Surface of Rear Suspension Arm Bracket
*b Edge of Rear Trailing Arm Assembly


Position the rear trailing arm assembly as shown in the illustration.

Reference Length (A):

116 mm (4.57 in.)



c.

Fully tighten the nut.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:

Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.



Hide 48738 2.INSTALL REAR SUSPENSION ARM COVER

a.

Engage the 4 claws and install the rear suspension arm cover.


Hide 48780E 3.INSTALL REAR TRAILING ARM ASSEMBLY

a.

Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.

Install the rear trailing arm assembly to the vehicle with the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 89516D 4.INSTALL SKID CONTROL SENSOR WIRE

a.

Install the skid control sensor wire to the rear trailing arm assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Engage the 2 clamps.


Hide 46430 5.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Install the No. 3 parking brake cable assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


Hide 48840A 6.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 57628C 7.INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 8.INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 10.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 11.PERFORM INITIALIZATION

Intelligent clearance sonar system
Simple intelligent parking assist system
(Click here)
Parking assist monitor system (Click here)
Automatic headlight beam level control system (Click here)