Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244742 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear trailing arm assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 57628C 2.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 3.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 46430 4.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C345058

Remove the nut and separate the No. 3 parking brake cable assembly from the rear trailing arm assembly.


Hide 89516D 5.SEPARATE SKID CONTROL SENSOR WIRE

a.
C348395

Disengage the 2 clamps.


b.

Remove the bolt and separate the skid control sensor wire from the rear trailing arm assembly.


Hide 48840A 6.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48780E 7.REMOVE REAR TRAILING ARM ASSEMBLY

a.
C345100C02
1.708,1.729 2.063,1.729 false 0.333,1.5 0.76,1.5 false 0.146,1.417 0.458,1.573 0.313,0.156 10 false *a 2.094,1.646 2.406,1.802 0.313,0.156 10 false *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C345069

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


c.
C345099

Remove the 4 bolts and rear trailing arm assembly.


Hide 48738 8.REMOVE REAR SUSPENSION ARM COVER

a.
C345101

Secure the rear trailing arm assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C345102

Disengage the 4 claws and remove the rear suspension arm cover.


Hide 48727 9.REMOVE REAR SUSPENSION ARM BRACKET

a.
C345103

Remove the bolt, nut and rear suspension arm bracket from the rear trailing arm assembly.

NOTICE:

Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.