Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM3210E _51 Engine / Hybrid System _047495 2ZR-FXE ENGINE MECHANICAL _0244907 ENGINE UNIT A

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system (w/ Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system (w/o Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration (Click here)
for SFI system (w/ Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
for SFI system (w/o Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 16331 1.REMOVE WATER OUTLET (w/ Flow Shutting Valve (Water Valve))

a.
A378473C02
0.583,1.573 0.771,1.573 0.771,1.573 0.948,1.25 true 2.938,1.354 3.26,0.229 3.26,0.229 3.083,0.229 true 2.708,1.969 2.594,1.969 2.594,1.969 2.531,1.708 true 0.344,1.521 0.563,1.688 0.219,0.167 10 true *1 2.875,0.177 3.094,0.344 0.219,0.167 10 false *3 2.781,1.906 3.031,2.073 0.25,0.167 10 true *2
*1 No. 9 Water By-pass Hose
*2 No. 7 Water by-pass Hose
*3 No. 4 Water By-pass Hose


Slide the clip and disconnect the No. 7 water by-pass hose from the No. 2 water by-pass hose.


b.

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR valve assembly with EGR cooler.


c.

Slide the clip and disconnect the No. 9 water by-pass hose from the purge valve.


d.

Remove the 2 nuts, water outlet and water outlet gasket from the cylinder head sub-assembly.


Hide 16331 2.REMOVE WATER OUTLET (w/o Flow Shutting Valve (Water Valve))

a.
A375786C01
0.5,1.417 0.646,1.417 0.646,1.417 0.917,1 true 2.26,1.708 2.406,1.708 2.406,1.708 2.677,1.292 true 0.302,1.365 0.5,1.552 0.198,0.188 10 true *1 2.031,1.615 2.229,1.802 0.198,0.188 10 true *2
*1 No. 9 water by-pass hose
*2 No. 4 water by-pass hose


Slide the clip and disconnect the No. 4 water by-pass hose from the EGR valve assembly with EGR cooler.


b.

Slide the clip and disconnect the No. 9 water by-pass hose from the purge valve.


c.

Remove the 2 nuts, water outlet and water outlet gasket from the cylinder head sub-assembly.


Hide 25610 3.REMOVE EGR PIPE ASSEMBLY

a.
A378474

Remove the 4 bolts and EGR pipe assembly, EGR pipe gasket and inlet EGR gasket.


Hide 25620 4.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

a.
A372584C01
0.958,1.427 1.208,1.656 0.25,0.229 10 true *a 1.51,1.875 1.76,2.063 0.25,0.188 10 true *a
V100135

Bolt
V100136

Nut
*a Stud bolt


Remove the bolt and 4 nuts.


b.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and EGR valve assembly with EGR cooler from the cylinder head sub-assembly and exhaust manifold (TWC: Front Catalyst).


c.

Remove the EGR cooler gasket.


Hide 17167 5.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 7.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 12261 8.DISCONNECT VENTILATION HOSE

Hide 15301 10.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 11.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16289 12.REMOVE NO. 5 WATER BY-PASS PIPE (w/ Exhaust Heat Recirculation System)

a.
A372586

Slide the clip and disconnect the No. 5 water by-pass pipe from the timing chain cover sub-assembly.


b.

Remove the 2 bolts and No. 5 water by-pass pipe from the cylinder block sub-assembly.


Hide 1628A 13.REMOVE NO. 6 WATER BY-PASS PIPE

a.
A372587

Slide the clip and disconnect the No. 6 water by-pass pipe from the water inlet sub-assembly.


b.

Remove the 2 bolts and No. 6 water by-pass pipe from the cylinder head sub-assembly.


Hide 17650G 14.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 15.REMOVE FUEL VAPOR FEED PIPE

a.
A372582

Remove the 2 bolts and fuel vapor feed pipe from the cylinder head cover sub-assembly.


Hide 23807 16.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 17.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 18.REMOVE FUEL INJECTOR ASSEMBLY

Hide 12261 19.REMOVE VENTILATION HOSE

a.
A372583

Slide the clip and remove the ventilation hose from the PCV valve (ventilation valve sub-assembly).