Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0244928 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Map Light Assembly (Front Dome Light)

·

Roof Wire (No. 1 Room Light Assembly)


WIRING DIAGRAM

w/o Sliding Roof


E341746E04
1.146,0.198 2.656,0.604 1.51,0.406 10 false from Auxiliary Battery 2.594,0.698 3.354,1.083 0.76,0.385 10 false 3K 2.594,1.573 3.354,1.958 0.76,0.385 10 false 3D 2.615,1.823 3.375,2.208 0.76,0.385 10 false 29 2.635,1.375 3.396,1.76 0.76,0.385 10 false 9 2.646,0.5 3.406,0.885 0.76,0.385 10 false 1 3.083,0.865 3.844,1.25 0.76,0.385 10 false DOME 4.083,1.354 4.917,1.75 0.833,0.396 10 false DOME CUT 5.5,0.708 6.26,1.094 0.76,0.385 10 false MB 5.521,0.51 6.281,0.896 0.76,0.385 10 false 23 5.552,1.813 6.313,2.198 0.76,0.385 10 false 1 5.896,0.583 6.656,0.969 0.76,0.385 10 false DOMR 5.906,1.906 6.667,2.292 0.76,0.385 10 false ILE 2.854,2.417 5.552,2.896 2.698,0.479 10 false Instrument Panel Junction Block Assembly 2.656,3.625 4.406,4.125 1.75,0.5 10 false Interior Light DOOR Switch 0.896,4.344 1.656,4.729 0.76,0.385 10 false +B1 2.052,4.688 3,5.135 0.948,0.448 10 false Personal Light Switch LH 3.115,4.156 3.875,4.542 0.76,0.385 10 false OFF 4.76,4.167 5.521,4.552 0.76,0.385 10 false 7 4.781,5.135 5.542,5.521 0.76,0.385 10 false 8 3.156,4.781 3.917,5.167 0.76,0.385 10 false ON 4.24,5.406 5,5.792 0.76,0.385 10 false GND9 3.708,6.24 4.469,6.625 0.76,0.385 10 false RLMP 3.719,6.469 4.479,6.854 0.76,0.385 10 false 5 4.333,6.469 5.094,6.854 0.76,0.385 10 false O3 4.344,6.625 5.854,7.063 1.51,0.438 10 false Map Light Assembly 5.229,7.563 6.875,8.042 1.646,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 1.219,8.135 3.063,8.552 1.844,0.417 10 false No. 1 Room Light Assembly 1.052,7.469 1.813,7.854 0.76,0.385 10 false 1 1.26,7.469 2.021,7.854 0.76,0.385 10 false B 2.563,7.271 3.323,7.656 0.76,0.385 10 false CTY 2.708,7.667 3.469,8.052 0.76,0.385 10 false E 2.906,7.667 3.667,8.052 0.76,0.385 10 false 2 2.917,7.26 3.677,7.646 0.76,0.385 10 false 3 5.49,2.021 6.25,2.406 0.76,0.385 10 false MB 2.604,2.031 3.365,2.417 0.76,0.385 10 false 3D 2.083,5.698 3.031,6.146 0.948,0.448 10 false Personal Light Switch RH 0.635,4.344 1.396,4.729 0.76,0.385 10 false 1 3.167,5.156 3.927,5.542 0.76,0.385 10 false ON 4.156,4.792 4.917,5.177 0.76,0.385 10 false ON 4.073,3.906 4.833,4.292 0.76,0.385 10 false OFF 4.26,4.167 4.698,4.563 0.438,0.396 10 false DOOR 3.125,5.781 3.885,6.167 0.76,0.385 10 false OFF 1.854,7.448 2.615,7.833 0.76,0.385 10 false DOOR 0.938,8.135 1.698,8.521 0.76,0.385 10 false O5


w/ Sliding Roof


E344001E04
3.031,2.802 5.719,3.417 2.688,0.615 10 false Instrument Panel Junction Block Assembly 3.615,4.052 5.313,4.375 1.698,0.323 10 false Interior Light DOOR Switch 3.604,4.708 4.938,5.292 1.333,0.583 10 false Interior Light ON/OFF Switch 2.531,5.271 3.438,5.729 0.906,0.458 10 false Personal Light Switch LH 1.896,7.396 3.51,7.781 1.615,0.385 10 false Personal Light Switch RH 4.021,7.958 5.333,8.292 1.313,0.333 10 false Map Light Assembly 5.813,7.958 6.969,8.583 1.156,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 1.302,9.208 3.073,9.573 1.771,0.365 10 false No. 1 Room Light Assembly 1.219,0.552 2.76,1 1.542,0.448 10 false from Auxiliary Battery 2.688,0.844 3.354,1.198 0.667,0.354 10 false 1 2.646,1.063 3.313,1.417 0.667,0.354 10 false 3K 2.698,1.74 3.365,2.094 0.667,0.354 10 false 9 2.667,2.198 3.333,2.552 0.667,0.354 10 false 29 2.656,1.938 3.323,2.292 0.667,0.354 10 false 3D 3.167,1.208 3.833,1.563 0.667,0.354 10 false DOME 5.563,1.063 6.229,1.417 0.667,0.354 10 false MB 5.583,0.865 6.25,1.219 0.667,0.354 10 false 23 5.969,2.271 6.635,2.625 0.667,0.354 10 false ILE 5.625,2.177 6.292,2.531 0.667,0.354 10 false 1 5.458,3.781 6.125,4.135 0.667,0.354 10 false 1 4.896,3.792 5.563,4.146 0.667,0.354 10 false DOOR 0.875,4.99 1.542,5.344 0.667,0.354 10 false +B1 0.479,4.99 1.146,5.344 0.667,0.354 10 false 10 5.438,7.135 6.104,7.49 0.667,0.354 10 false 11 4.99,7.396 5.656,7.75 0.667,0.354 10 false GND 3.604,7.552 4.271,7.906 0.667,0.354 10 false RLMP 4.021,7.802 4.688,8.156 0.667,0.354 10 false O4 2.979,8.333 3.646,8.688 0.667,0.354 10 false 3 2.979,8.729 3.646,9.083 0.667,0.354 10 false 2 2.604,8.344 3.271,8.698 0.667,0.354 10 false CTY 2.771,8.729 3.438,9.083 0.667,0.354 10 false E 1.052,9.219 1.719,9.573 0.667,0.354 10 false O5 2.656,2.385 3.323,2.74 0.667,0.354 10 false 3D 4.125,1.708 5.094,2.052 0.969,0.344 10 false DOME CUT 5.99,0.969 6.656,1.323 0.667,0.354 10 false DOMR 5.563,2.385 6.229,2.74 0.667,0.354 10 false MB 1.865,8.521 2.531,8.875 0.667,0.354 10 false DOOR 1.313,8.552 1.979,8.906 0.667,0.354 10 false B 3.615,7.813 4.281,8.167 0.667,0.354 10 false 2 1.094,8.552 1.76,8.906 0.667,0.354 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system.* ON or OFF -

*: Refer to System Description for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

All lights that are controlled by the illuminated entry system come on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof
Tester Connection Condition Specified Condition
O4-10 (+B1) - O4-2 (RLMP) No. 1 room light switch in DOOR position Below 1 Ω
No. 1 room light switch in ON position 10 kΩ or higher
O4-10 (+B1) or O4-2 (RLMP) - Body ground No. 1 room light switch in DOOR position 10 kΩ or higher

w/o Sliding Roof
Tester Connection Condition Specified Condition
O3-1 (+B1) - O3-5 (RLMP) No. 1 room light switch in DOOR position Below 1 Ω
No. 1 room light switch in ON position 10 kΩ or higher
O3-1 (+B1) - O3-5 (RLMP) - Body ground No. 1 room light switch in DOOR position 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)

NG

REPLACE ROOF WIRE(NO. 1 ROOM LIGHT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O4-10 (+B1) - Body ground*1 Battery saving function not operating 11 to 14 V
O3-1 (+B1) - Body ground*2 Battery saving function not operating 11 to 14 V


*1: w/ Sliding Roof

*2: w/o Sliding Roof



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof
Tester Connection Condition Specified Condition
O4-1 (DOOR) - 3D-29 Always Below 1 Ω
O4-1 (DOOR) or 3D-29 - Body ground Always 10 kΩ or higher

w/o Sliding Roof
Tester Connection Condition Specified Condition
O3-7 (DOOR) - 3D-29 Always Below 1 Ω
O3-7 (DOOR) or 3D-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E333581C04
1.333,0.365 1.625,0.583 0.292,0.219 4.76,0.5 5.052,0.719 0.292,0.219 3.302,1.125 3.531,1.479 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.406,0.406 1.865,0.635 0.458,0.229 10 false 3D 4.813,0.542 5.271,0.771 0.458,0.229 10 false MB 3.604,1.448 4.063,1.677 0.458,0.229 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3D-29 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY