Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P300449  High Voltage Power Resource Circuit Abort Pre-Charge  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

HV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU malfunction

·

HV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



INSPECTION DESCRIPTION


A378826E03
0.51,0.271 1.917,0.427 1.406,0.156 10 false Service Plug Grip 0.813,2.115 1.563,2.323 0.75,0.208 10 false HV Battery 1.99,1.125 2.427,1.323 0.438,0.198 10 false SMRB 1.979,2 2.417,2.198 0.438,0.198 10 false SMRG 1.969,2.573 2.406,2.771 0.438,0.198 10 false SMRP 4.594,2.042 5.708,2.281 1.115,0.24 10 false Boost Converter 5.865,2.042 6.563,2.24 0.698,0.198 10 false Inverter 4.438,2.896 6.552,3.115 2.115,0.219 10 false Inverter with Converter Assembly 1.365,3.438 3.729,3.667 2.365,0.229 10 false HV Battery Junction Block Assembly 5.198,4.344 7.01,4.563 1.813,0.219 10 false Hybrid Vehicle Control ECU 1.146,4.75 2.708,4.979 1.563,0.229 10 false : High Voltage Line 1.156,5.073 2.531,5.292 1.375,0.219 10 false : Inspection Areas 4.75,3.677 4.99,3.875 0.24,0.198 10 false *a 2.563,0.531 2.813,0.74 0.25,0.208 10 false *b 3.813,0.76 4.052,0.958 0.24,0.198 10 false *c 0.365,0.542 0.771,0.708 0.406,0.167 10 false *d, *e 5.479,3.656 6.438,4.042 0.958,0.385 10 false System main relay signal 2.51,2.563 3.385,2.948 0.875,0.385 10 false System Main Resistor

System Diagram Range Inspection Content Reason Inspection Step
*a Check connection condition and wire harness continuity between hybrid vehicle control ECU and HV battery junction block assembly In order to check whether connectors are connected properly and to check for an open circuit in the SMRP and SMRB primary lines 3 to 7
*b Check system main relay Check whether SMRB and SMRP stuck OFF 8, 9
*c Check connection condition and high-voltage cable continuity between HV battery junction block assembly and inverter with converter assembly Check for open circuit and defective connection (arc marks) due to looseness 10 to 12
*d Check high-voltage cable and connection condition between HV battery and HV battery junction block assembly Check for open circuit and defective connection (arc marks) due to looseness 13, 14, 15, 16, 21
*e Check HV battery Check whether HV battery voltage has drastically dropped below normal range 17


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and the inverter with converter assembly and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P300449 High Voltage Power Resource Circuit Abort Pre-Charge Although a system main relay operation signal was sent when the power switch was operated, the system voltage is not sufficiently increased after boosting and the HV battery current does not flow.
High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.
The EV electric battery fuse is blown, the service plug grip is removed, the system main resistor is blown, SMRP or SMRB remains open, or the high-voltage cable has an open circuit.
(2 trip detection logic)
·

HV battery junction block assembly

·

HV floor under wire

·

Inverter with converter assembly

·

HV battery

·

Wire harness or connector

·

Hybrid battery terminal block


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P300449
·

Hybrid Battery Voltage

·

Hybrid Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal

·

Inter Lock Switch

·

SMRP Status

·

SMRB Status

·

SMRG Status


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P300449 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
P0AFC96 Hybrid/EV Battery Sensor Module Component Internal Failure
P0AFC00 Hybrid/EV Battery Sensor Module
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety μC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Hybrid control system P0AFC16 Hybrid/EV Battery Sensor Module Circuit Voltage Below Threshold
Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P0B3B14 Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
P0B4014 Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
P0B4514 Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
P0B4A14 Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
P0B4F14 Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
P0B5414 Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
P0B5914 Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
P0B5E14 Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
P0B6314 Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
P0B6814 Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
P308A13 Hybrid/EV Battery Voltage Sensor All Circuit Open
P0AFC62 Hybrid/EV Battery Sensor Module Signal Compare Failure
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P308A12 Hybrid/EV Battery Voltage Sensor All Circuit Short to Auxiliary Battery
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short
P1C8249 High Voltage Power Resource Circuit Over Loading
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P0CA300 DC/DC Converter Step Up Voltage Performance

HINT:
·

P300449 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P300449.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Both of the following conditions are met:
·

"VH-Voltage after Boosting" is below 50 V.

·

Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is 40 V or less.


A
Except above B



e.

Turn the power switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the M37 HV battery junction block assembly connector.


d.

Disconnect the F2 hybrid vehicle control ECU connector.


e.
A369410C21
2.604,3.333 3.073,3.604 0.469,0.271 1.406,0.167 1.875,0.438 0.469,0.271 1.354,3.573 0.979,4.083 false 1.26,1.313 1.708,1.917 false 1.063,1.323 0.813,1.906 false 1.625,3.594 2,4.073 false 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.531,0.219 1.865,0.396 0.333,0.177 10 false F2 2.719,3.385 3.052,3.563 0.333,0.177 10 false M37 1.552,1.938 2.167,2.135 0.615,0.198 10 false SMRB 0.75,4.094 1.365,4.292 0.615,0.198 10 false SMRB 0.552,1.938 1.167,2.135 0.615,0.198 10 false SMRP 1.813,4.094 2.427,4.292 0.615,0.198 10 false SMRP
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-16 (SMRB) - M37-1 (SMRB) Power switch off Below 1 Ω
F2-15 (SMRP) - M37-2 (SMRP) Power switch off Below 1 Ω



f.

Reconnect the F2 hybrid vehicle control ECU connector.


g.

Reconnect the M37 HV battery junction block assembly connector.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the M37 HV battery junction block assembly connector.


d.
A365602C04
2.677,1.083 3.031,1.344 0.354,0.26 1.896,1.25 2.292,1.823 false 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 2.719,1.125 3.031,1.281 0.313,0.156 10 false M37
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M37-3 (GND) - Body ground Power switch off Below 1 Ω



e.

Reconnect the M37 HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

8.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

A378136C34
3.844,1.073 4.208,1.281 0.365,0.208 3.167,0.208 3.552,0.427 0.385,0.219 5.635,0.177 5.979,0.396 0.344,0.219 3.385,1.188 3.094,1.354 true 3.604,1.188 3.844,1.375 true 3.771,0.396 3.406,0.667 true 5.813,0.708 6.313,1.125 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 3.708,1.385 4.167,1.563 0.458,0.177 10 true SMRB 2.927,1.385 3.281,1.573 0.354,0.188 10 true GND 3.854,0.302 4.167,0.469 0.313,0.167 10 true CBI 3.896,1.104 4.208,1.26 0.313,0.156 10 false M37 3.26,0.24 3.5,0.396 0.24,0.156 10 true S4 6.396,1.115 6.573,1.313 0.177,0.198 10 true + 5.708,0.198 5.927,0.375 0.219,0.177 10 true A
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (+) - S4-1 (CBI) Auxiliary battery voltage applied between terminals M37-1 (SMRB) and M37-3 (GND) Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M37-1 (SMRB) - M37-3 (GND) -40 to 80°C (-40 to 176°F) 20.6 to 40.8 Ω



e.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

9.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

9.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

A378136C44
3.844,1 4.208,1.208 0.365,0.208 1.156,0.167 1.521,0.375 0.365,0.208 2.24,0.177 2.604,0.385 0.365,0.208 3.531,1.188 3.719,1.375 true 3.385,1.177 3.177,1.365 true 1.323,0.656 0.74,0.958 true 2.063,0.542 2.385,0.656 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 3.896,1.031 4.208,1.188 0.313,0.156 10 false M37 3.031,1.396 3.396,1.573 0.365,0.177 10 true GND 3.615,1.396 4.063,1.573 0.448,0.177 10 true SMRP 0.615,0.969 0.781,1.115 0.167,0.146 10 true - 1.208,0.188 1.49,0.354 0.281,0.167 10 true z12 2.302,0.198 2.542,0.344 0.24,0.146 10 true S3 1.76,0.458 2.031,0.625 0.271,0.167 10 true CEI
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
z12-1 (-) - S3-1 (CEI) Auxiliary battery voltage applied between terminals M37-2 (SMRP) and M37-3 (GND) 24.3 to 29.7 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M37-2 (SMRP) - M37-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω



e.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (HV FLOOR UNDER WIRE)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (HV FLOOR UNDER WIRE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A376137

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

Disconnect the HV floor under wire from the inverter with converter assembly.


d.

Check for arc marks at the terminals for the HV floor under wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



e.

Reconnect the HV floor under wire.



A

11.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV FLOOR UNDER WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

11.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV FLOOR UNDER WIRE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376114

Check that the HV floor under wire is connected securely, and there are no contact problems.


d.

Disconnect the HV floor under wire connectors from the HV battery junction block assembly.


e.

Check for arc marks on the terminals of the HV floor wire and the HV battery junction block assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the HV floor under wire connectors to the HV battery junction block assembly.


g.

Install the No. 1 HV battery cover panel RH.



A

12.CHECK HV FLOOR UNDER WIRE (INVERTER WITH CONVERTER ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

12.CHECK HV FLOOR UNDER WIRE (INVERTER WITH CONVERTER ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376114

Disconnect the HV floor under wire connectors from the HV battery junction block assembly.


d.
A376129

Disconnect the HV floor under wire connector from the inverter with converter assembly.


e.

Measure the resistance according to the value(s) in the table below.

A378816C05
1.875,0.802 2.188,1.021 0.313,0.219 3.802,0.521 4.115,0.74 0.313,0.219 5.677,0.521 5.99,0.74 0.313,0.219 4.396,0.698 4.073,1.094 false 5.333,0.708 5.708,1.115 false 1.906,1.635 1.26,2.042 false 2.229,1.635 2.771,2.042 false 1.25,1.24 1.604,1.24 false 0.865,0.583 1.177,0.74 0.313,0.156 10 false *a 3.708,0.167 4.021,0.323 0.313,0.156 10 false *b 1.948,0.833 2.26,0.99 0.313,0.156 10 false S1 3.875,0.552 4.188,0.708 0.313,0.156 10 false S4 5.76,0.563 6.073,0.719 0.313,0.156 10 false S3 3.813,1.042 4.125,1.198 0.313,0.156 10 false CBI 5.76,1.073 6.073,1.229 0.313,0.156 10 false CEI 0.979,1.99 1.292,2.146 0.313,0.156 10 false CBI 2.875,1.979 3.188,2.135 0.313,0.156 10 false CEI 1.063,1.188 1.375,1.344 0.313,0.156 10 false *1
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)
*b HV Floor Under Wire
(HV Battery Junction Block Assembly Side)


Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (CBI) - S4-1 (CBI) Power switch off Below 1 Ω
S1-2 (CEI) - S3-1 (CEI) Power switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.



f.

Reconnect the HV floor under wire connector to the inverter with converter assembly.


g.

Reconnect the HV floor under wire connectors to the HV battery junction block assembly.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

13.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

13.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376113

Check the HV battery high voltage cable is connected securely, and there are no contact problems.


d.

Disconnect the 2 HV battery high voltage cable connectors from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



e.

Check for arc marks on the terminals of the HV battery high voltage terminals.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Reconnect the 2 HV battery high voltage cable connectors.


g.

Install the No. 1 HV battery cover panel RH.



A

14.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

14.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.
A375907

Check that the HV battery high voltage cable is connected securely, and there are no contact problems.


d.

Remove the hybrid battery terminal block.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



e.

Check for arc marks on the terminals of the HV battery high voltage terminals.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Install the hybrid battery terminal block.


g.

Install the No. 1 HV battery shield panel.



A

15.CHECK HV BATTERY HIGH VOLTAGE CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

15.CHECK HV BATTERY HIGH VOLTAGE CABLE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A378852N02
0.167,0.24 0.427,0.49 0.26,0.25 0.208,0.26 0.365,0.458 0.156,0.198 10 true A

Disconnect the A HV battery high voltage cable connector from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
A378850C02
0.198,1.146 0.448,1.333 0.25,0.188 1.083,1.281 1.594,1.885 true 1.083,4.094 1.646,3.531 true 2.479,4.135 1.969,3.542 true 0.031,0.115 0.344,0.271 0.313,0.156 10 false *a 0,2.448 0.24,2.594 0.24,0.146 10 true *b 1.656,1.917 1.813,2.115 0.156,0.198 10 false + 0.281,1.177 0.448,1.323 0.167,0.146 10 false A 1.01,4.125 1.167,4.323 0.156,0.198 10 true 1 2.469,4.156 2.625,4.354 0.156,0.198 10 true 2
*a High Voltage Cable
(HV Battery Junction Block Assembly Side)
*b Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (+) - Service plug grip connecting terminal 2 Power switch off Below 1 Ω



e.

Reconnect the A HV battery high voltage cable connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

16.CHECK HV BATTERY HIGH VOLTAGE CABLE

NG

16.CHECK HV BATTERY HIGH VOLTAGE CABLE
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.
A378135

Remove the bolt from the hybrid battery terminal block.


d.
A376126N04
1.365,1.229 1.771,1.49 0.406,0.26 1.427,1.271 1.708,1.448 0.281,0.177 10 true z20

Disconnect the z20 high voltage connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



e.
A380647C04
0.594,1.313 0.958,1.552 0.365,0.24 1.24,3.948 1.656,3.531 true 2.354,3.969 1.958,3.552 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.063,2.448 0.375,2.604 0.313,0.156 10 true *b 0.646,1.354 0.958,1.552 0.313,0.198 10 false z20 1.104,3.979 1.302,4.167 0.198,0.188 10 true 1 2.365,3.99 2.563,4.177 0.198,0.188 10 true 2
*a High Voltage Cable
(Hybrid Battery Terminal Block Side)
*b Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z20-1 - Service plug grip connecting terminal 1 Power switch off Below 1 Ω



f.

Reconnect the z20 high voltage connector to the hybrid battery terminal block.


g.

Install the bolt to the hybrid battery terminal block.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>INSTALLATION


h.

Install the No. 1 HV battery shield panel.


Result:
Proceed to
OK
NG



OK

17.CHECK HV BATTERY

NG

17.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A378851N03
2.906,1.229 3.271,1.49 0.365,0.26 2.948,1.271 3.24,1.458 0.292,0.188 10 true z12

Disconnect the z12 HV battery high voltage cable connector from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
A378849C05
0.563,1.156 0.927,1.375 0.365,0.219 1.979,3.521 2.479,4.177 true 1.656,3.521 1.146,4.167 true 1.708,1.365 2.208,2.021 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.01,2.458 0.229,2.625 0.219,0.167 10 true *b 1.052,4.219 1.25,4.375 0.198,0.156 10 true 1 2.427,4.219 2.625,4.375 0.198,0.156 10 true 2 0.646,1.188 0.958,1.344 0.313,0.156 10 false z12 2.271,1.969 2.469,2.125 0.198,0.156 10 true -
*a High Voltage Cable
(HV Battery Junction Block Assembly Side)
*b Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-1 (-) - Service plug grip connecting terminal 1 Power switch off 100 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.



e.

Reconnect the z12 HV battery high voltage cable connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

18.CHECK FOR INTERMITTENT PROBLEMS

NG

21.CHECK HYBRID BATTERY TERMINAL BLOCK
18.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
Problem symptom does not recur.
Problem symptom recurs.


HINT:
·

Since 2 trip detection logic is used, the DTC detection condition must be met twice.

·

If DTC P300449 is output again after performing the inspection, replace the inverter with converter assembly. If DTC P300449 is not output again, replace the HV battery junction block assembly.




Problem symptom does not recur.

19.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

Problem symptom recurs.

REPLACE INVERTER WITH CONVERTER ASSEMBLY

19.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

20.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
20.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C8449

Result:
Result Proceed to
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. B



A

END

B

21.CHECK HYBRID BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Remove the Hybrid battery terminal block.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL


b.
A367707C01
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1
*1 Hybrid Battery Terminal Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hybrid battery terminal block Always Below 1 Ω



c.

Install the Hybrid battery terminal block.


Result:
Proceed to
OK
NG



OK

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK