Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0244771 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 5.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 55735A 6.REMOVE WATER GUARD PLATE LH

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 82121 10.DISCONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A376292

Move each lock lever as shown in the illustration and disconnect the 2 inverter with converter assembly connectors.

NOTICE:
·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Insulate the disconnected terminals with insulating tape.

·

Do not touch the waterproof seal or terminals of the connector.




b.
A376389

Remove the bolt.


c.

Disengage the 2 clamps and disconnect the engine wire.


Hide 13.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 15.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 16.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 17.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 18.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 19.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76973F 20.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76971G 21.REMOVE REAR UNDER COVER

Hide 71033 22.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N4A 23.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 24.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A375877C01
1.906,1.26 2.406,1.26 true 2.427,1.167 2.688,1.365 0.26,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.


b.

Disconnect the shield ground from the HV battery.


Hide 58390 25.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY

Hide 58165B 26.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>2ZR-FXE INTAKE / EXHAUST>EXHAUST MANIFOLD>REMOVAL


Hide 51201 27.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 46420 28.DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.
A376390

Remove the 2 bolts and disconnect the No. 2 parking brake cable assembly.


Hide 821H1 29.REMOVE HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A378131

Remove the 2 nuts.


b.

Remove the 3 clamps.

A371693

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A378133

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.
A371688C01
0.052,0.25 0.375,0.49 0.323,0.24 12 true *A 0.042,2.573 0.365,2.813 0.323,0.24 12 true *B 0.76,1.49 0.969,1.688 0.208,0.198 10 true A 0.938,3.74 1.146,3.938 0.208,0.198 10 true A 3.01,1.51 3.219,1.708 0.208,0.198 10 true B 2.885,3.875 3.094,4.073 0.208,0.198 10 true B
*A for LHD
*B for RHD


Remove the clamp (A).


e.

Disengage the clamp (B) to remove the HV floor under wire.