2005-2008 RAV4 · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL TIE ROD END SUB-ASSEMBLY LH

  1. F040050E20
    Screw the lock nut and tie rod end sub-assembly LH on the rack end until the matchmarks are aligned and temporarily tighten the lock nut.

    HINT:
    Fully tighten the lock nut after adjusting toe-in.


2. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the tie rod end sub-assembly LH.


3. INSTALL STEERING GEAR ASSEMBLY

C128838
  1. Install the steering gear onto the front suspension crossmember with the 2 bolts and 2 nuts.

    Torque:
    138 N*m{ 1407 kgf*cm , 102 ft.*lbf }

    NOTICE:
    Keep the nut from rotating while turning the bolt.


4. INSTALL INTERMEDIATE SHAFT

C132129E02
  1. Align the matchmarks and install the intermediate shaft onto the steering gear.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


5. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
  1. Install the column hole cover onto the steering gear with a new clamp.


6. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. for 1AZ-FE:
    Install the engine with transaxle (Click here).

  1. for 2AZ-FE:
    Install the engine with transaxle (Click here).

  1. for 2AD-FHV
    Install the engine with transaxle (Click here).

  1. for 2AD-FTV
    Install the engine with transaxle (Click here).


7. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  1. C128837E02
    Attach clip B onto the body portion and install the No. 1 hole cover onto the body portion with clip A.

    NOTICE:
    Make sure that the lip portion of the No. 1 hole cover is not damaged.


8. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

C128488
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


9. INSTALL COLUMN HOLE COVER SILENCER SHEET

C128486
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


10. CONNECT TIE ROD END SUB-ASSEMBLY LH

C132132
  1. Connect the tie rod end onto the steering knuckle with the castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut up to 60° further.

  1. Install a new cotter pin.


11. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


12. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

14. POSITION FRONT WHEELS FACING STRAIGHT AHEAD

15. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the wheel alignment (Click here).

← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →