2005-2008 RAV4 · Service Manual BRAKE

C0210/33 Right Rear Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built from Aug 2008

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

DESCRIPTION

Refer to DTC C0200/31 (Click here).
DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.
DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When one of following conditions is met:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  1. Skid control sensor (2WD)
  2. Rear speed sensor (4WD)
  3. Skid control sensor circuit (2WD)
  4. Rear speed sensor circuit (4WD)
  5. Sensor installation
  6. Foreign matter on sensor rotor
  7. Brake actuator (Skid control ECU)
C1238/38
C1239/39
When either condition below is met:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise continues for 5 seconds or more in sensor signal from abnormal wheel.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Skid control sensor (2WD)
  2. Rear speed sensor (4WD)
  3. Skid control sensor circuit (2WD)
  4. Rear speed sensor circuit (4WD)
  5. Sensor installation
  6. Brake actuator (Skid control ECU)
C1273/73
C1274/74
Detected only during test mode.
  1. Skid control sensor (2WD)
  2. Rear speed sensor (4WD)
  3. Skid control sensor circuit (2WD)
  4. Rear speed sensor circuit (4WD)
  5. Sensor installation
  6. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Skid control sensor (2WD)
  2. Rear speed sensor (4WD)
  3. Skid control sensor circuit (2WD)
  4. Rear speed sensor circuit (4WD)
  5. Sensor installation

HINT:
  1. DTC C0210/33 and C1238/38 relate to the skid control sensor RH.
  2. DTC C0215/34 and C1239/39 relate to the skid control sensor LH.


WIRING DIAGRAM

C136041E05

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in the test mode after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness corresponding to a DTC (Click here).

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    Result 
    Result
    Proceed to
    There are momentary interruptions
    A
    There are no momentary interruptions
    B
    There is a constant open circuit (for 2WD)
    C
    There is a constant open circuit (for 4WD)
    D

    HINT:
    Perform this inspection before removing the sensor and connector.



B
Go to step 4

C
Go to step 7

D
Go to step 14
A


2. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruptions between the skid control ECU and rear speed sensor (Click here).

  1. Check that there are no momentary interruptions.


NEXT


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


4. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Check the Data List for proper functioning of the rear speed sensor.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    RR Wheel Speed
    Wheel speed sensor (RR) reading: Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Similar to speed indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading: Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Similar to speed indicated on speedometer

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.

Result 
Result
Proceed to
OK
A
NG (for 2WD)
B
NG (for 4WD)
C


B
Go to step 7

C
Go to step 14
A


5. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a test mode inspection and check for DTCs (Click here).

    OK:
    All Test Mode DTCs are cleared.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2WD)
    B
    NG (for 4WD)
    C



B
Go to step 7

C
Go to step 14
A


6. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output (for 2WD)
    B
    DTC output (for 4WD)
    C



B
Go to step 12

C
Go to step 19
A

USE SIMULATION METHOD TO CHECK

7. CHECK REAR SKID CONTROL SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C144931E05
    Check the skid control sensor installation.

    OK:
    There is no clearance between the sensor and rear axle hub.



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

  1. C169030E04
    Disconnect the skid control sensor wire.

  1. Disconnect the X1 and/or W1 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    X1 ("A"-2) - X1 ("B"-1)
    Always
    Below 1 Ω
    X1 ("A"-2) - X1 ("B"-2)
    Always
    10 kΩ or higher
    X1 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    X1 ("A"-1) - X1 ("B"-2)
    Always
    Below 1 Ω
    X1 ("A"-1) - X1 ("B"-1)
    Always
    10 kΩ or higher
    X1 ("A"-1) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    W1 ("A"-2) - W1 ("B"-1)
    Always
    Below 1 Ω
    W1 ("A"-2) - W1 ("B"-2)
    Always
    10 kΩ or higher
    W1 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    W1 ("A"-1) - W1 ("B"-2)
    Always
    Below 1 Ω
    W1 ("A"-1) - W1 ("B"-1)
    Always
    10 kΩ or higher
    W1 ("A"-1) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Connect the skid control sensor wire.

C195807E01
  1. Disconnect the X1 and/or W1 sensor connector.

  1. Disconnect the A27 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A27-11 (RL+) - X1-2
    Always
    Below 1 Ω
    A27-12 (RL-) - X1-1
    Always
    Below 1 Ω
    A27-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    A27-12 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A27-33 (RR+) - W1-2
    Always
    Below 1 Ω
    A27-34 (RR-) - W1-1
    Always
    Below 1 Ω
    A27-33 (RR+) - Body ground
    Always
    10 kΩ or higher
    A27-34 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK SKID CONTROL ECU (SENSOR INPUT)

  1. C195808E01
    Disconnect the X1 and/or W1 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    X1-2 - Body ground
    Ignition switch on (IG)
    8.2 to 14 V
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    W1-2 - Body ground
    Ignition switch on (IG)
    8.2 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


11. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
USE SIMULATION METHOD TO CHECK
A


12. REPLACE SKID CONTROL SENSOR AND SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear axle hub and bearing assembly (Click here).

    HINT:
    The rear speed sensor rotor and skid control sensor are built into the rear axle hub and bearing assembly. If the rear speed sensor rotor and skid control sensor need to be replaced, replace the rear axle hub and bearing assembly.


NEXT


13. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY

14. CHECK REAR SPEED SENSOR INSTALLATION

  1. C144929E17
    Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle carrier.
    The installation bolt is tightened properly.

    Torque:
    8.5 N*m (87 kgf*cm, 75 in.*lbf)



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


15. CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here ).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


16. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Disconnect the A27 ECU connector.

  1. Disconnect the K28 and/or K29 sensor connector.

C195809E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A27-11 (RL+) - K28-1
    Always
    Below 1 Ω
    A27-12 (RL-) - K28-2
    Always
    Below 1 Ω
    A27-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    A27-12 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A27-33 (RR+) - K29-1
    Always
    Below 1 Ω
    A27-34 (RR-) - K29-2
    Always
    Below 1 Ω
    A27-33 (RR+) - Body ground
    Always
    10 kΩ or higher
    A27-34 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. CHECK SKID CONTROL ECU (SENSOR INPUT)
C195810E01
  1. Disconnect the K28 and/or K29 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    K28-1 - Body ground
    Ignition switch on (IG)
    8.2 to 14 V
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 - Body ground
    Ignition switch on (IG)
    8.2 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


18. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
USE SIMULATION METHOD TO CHECK
A


19. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).


NEXT


20. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


21. REPLACE REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear axle hub and bearing assembly (Click here).

    HINT:
    The rear speed sensor rotor is built into the rear axle hub and bearing assembly. If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.


NEXT


22. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C0210/33 Right Rear Wheel Speed Sensor Signal (+ 7 more codes) (Aug 2007 – Jul 2008)C0226/21 SFR Solenoid Circuit (+ C0236/22, C0246/23, C0256/24) (Nov 2005 – Dec 2006) →