C1425 Open in Stop Light Switch Circuit
Diagnostic trouble codes · Vehicles built from Aug 2008
DESCRIPTION
The skid control ECU (housed in the brake actuator assembly) inputs stop light switch signals and the condition of brake operation.The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1425 |
When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit continues for 3 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed.
ON
Brake pedal released.
OFF
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the intelligent tester (Click here).
ABS/VSC/TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
- Result:
Result
Proceed to
DTC (C1425) is not output.
A
DTC (C1425) is output.
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 4. INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL) |
Make sure that there is no looseness in the locking part and connecting part of the connectors.

Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A66-2 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 5. INSPECT STOP LIGHT SWITCH |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin not pushed in
Below 1 Ω
1 - 2
Switch pin pushed in
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT SKID CONTROL ECU (STP2 TERMINAL) |
Connect the stop light switch connector.
Install the stop light control relay (BRK).
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A67-22 (STP2) - Body ground
Brake pedal depressed ←→ released
Output voltage changes
|
|
||||
| OK | |
| 7. RECONFIRM DTC |
Connect the skid control ECU connector.
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
- Result:
Result
Proceed to
DTC (C1425) is not output.
A
DTC (C1425) is output.
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM NO. 1 RELAY BLOCK) |
Turn the ignition switch off.

Remove the stop light control relay (BRK).
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A67-2 (STP) - Stop light control relay (BRK) terminal 3
Always
Below 1 Ω
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
