2005-2008 RAV4 · Service Manual BRAKE

C1426 Stop Light Switch OFF Stuck Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The skid control ECU (housed in the brake actuator assembly) inputs stop light switch signals and the condition of brake operation.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC Code
DTC Detection Condition
Trouble Area
C1426
When the brake pedal load sensing switch is on, the master cylinder pressure is 2 MPa or more and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch is off for 2 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Stop light control relay
  5. Stop light control relay circuit
  6. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

Refer to DTC C1425 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
Go to step 4
OK


2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond the specified point
    OFF: Brake pedal not depressed beyond the specified point
    -

  1. Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.

  1. Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.

    OK:
    First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.


    Result:
    Result
    Proceed to
    OK
    A
    NG
    Turning on of the stop light switch is not confirmed.
    B
    The brake pedal load sensing switch turns on first.
    C



B
Go to step 9

C
Go to step 10
A


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC (C1426) is not output.
    A
    DTC (C1426) is output.
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

4. INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)

  1. C194434E02
    Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A66-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5. INSPECT STOP LIGHT SWITCH

  1. C194435E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed in
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


6. INSPECT STOP LIGHT CONTROL RELAY (BRK)

  1. C126459E12
    Remove the stop light control relay (BRK).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE STOP LIGHT CONTROL RELAY (BRK)
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM NO. 1 RELAY BLOCK)

  1. C194436E02
    Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-2 (STP) - Stop light control relay (BRK) terminal 3
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


8. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the relay, reconnect the connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)

9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM NO. 1 RELAY BLOCK)

  1. C194436E02
    Turn the ignition switch off.

  1. Remove the stop light control relay (BRK).

  1. Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-2 (STP) - Stop light control relay (BRK) terminal 3
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

10. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Click here).

    OK:
    The brake pedal height and stop light switch installation are normal.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY (BRAKE PEDAL LOAD SENSING SWITCH) (Click here)


← C1425 Open in Stop Light Switch Circuit (from Aug 2008)C1427 Motor Malfunction (from Aug 2008) →