2005-2008 RAV4 · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL PISTON

  1. A032958E02
    Using a small screwdriver, install a new snap ring onto one end of the piston pin hole.

    HINT:
    Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.

  1. Gradually heat the piston up to 80 to 90°C (176 to 194°F).

  1. A098154E01
    Align the front marks of the piston and connecting rod, then push in the piston pin with your thumb until the pin comes into contact with the snap pin hole.

    HINT:
    Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.


2. INSTALL PISTON RING SET

  1. A131712E01
    Install the expander and oil ring by hand.

    HINT:
    1. Install the expander and oil ring so that their ring ends are at opposite sides.
    2. Securely install the expander to the oil ring's inner groove.

  1. A098156E02
    Using a piston ring expander, install the 2 compression rings with the paint mark as shown in the illustration.

    NOTICE:
    Install the No. 2 compression ring with the cord mark (2N) facing upward.

  1. A132606E01
    Position the piston rings so that the ring ends are as shown in the illustration.


3. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A112263E01
    Install the 4 oil nozzles with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


4. INSTALL CYLINDER BLOCK WATER JACKET SPACER

A112265

5. INSTALL CRANKSHAFT BEARING

  1. A053029E02
    Install the upper bearing with an oil groove onto the cylinder block.

    NOTICE:
    Do not apply engine oil to the bearing its contact surface.


6. INSTALL NO. 2 CRANKSHAFT BEARING

  1. A033379E01
    Install the lower bearing onto the bearing cap.

    NOTICE:
    Do not apply engine oil to the bearing its contact surface.


7. INSTALL CRANKSHAFT THRUST WASHER UPPER

  1. A013501E01
    Install the 2 thrust washers onto the No. 3 journal position of the cylinder block with the oil groove facing outward.


8. INSTALL CRANKSHAFT
  1. Apply engine oil to the upper bearing, and install the crankshaft onto the cylinder block.

  1. A098155E01
    Examine the front marks and numbers, and install the bearing caps onto the cylinder block in the order shown in the illustration.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A087780E04
    Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A098354E01
    Mark the front of the bearing cap bolts with paint.

  1. Retighten the 10 bearing cap bolts by 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.


9. INSTALL CONNECTING ROD BEARING

  1. A098158E01
    Align the bearing claw with the oil groove of the connecting rod or connecting rod cap.

    NOTICE:
    Do not apply engine oil to the bearing or its contact surface.


10. INSTALL PISTON WITH CONNECTING ROD
  1. Apply engine oil to the cylinder walls, pistons, and surfaces of connecting rod bearings.

  1. A132606E01
    Check the position of the piston ring ends.

  1. A112258E01
    Using a hammer handle and piston ring compressor, press a piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.

  1. A098145E01
    Check that the front mark of the connecting rod cap is facing in the correct direction.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.

  1. Using a 12 mm socket wrench, tighten the bolts in several passes to the specified torque.

    Torque:
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. A101478E03
    Mark the front of the connecting rod bolts with paint.

  1. Retighten the cap bolts 90°as shown in the illustration.

  1. Check that the crankshaft turns smoothly.


11. INSTALL BALANCE SHAFT BEARING

  1. A128204E01
    Align the bearing claw with the claw groove, and push in the 8 bearings.

    NOTICE:
    Do not apply engine oil to the bearing its contact surface.

  1. Apply a light coat of engine oil in the bearings.


12. INSTALL BALANCE SHAFT

  1. A090850E02
    Rotate the No. 1 driven gear of the No. 1 balance shaft in the rotating direction until it hits the stopper.

  1. A128214E01
    Confirm that the timing marks on the No. 1 and No. 2 driven gears are aligned.

  1. A131707E01
    Align the timing marks of the No. 1 and No. 2 balance shafts as shown in the illustration.

  1. Place the No. 1 and No. 2 balance shafts onto the crankcase.

  1. Apply a light coat of engine oil to the threads and under the heads of the bolts.

  1. A128197E03
    Using several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    21.6 N*m{ 220 kgf*cm , 16 ft.*lbf }

  1. Mark the front of the bolts with paint.

  1. Retighten the bolts 90°as shown in the illustration.

  1. A037134E02
    Check that the paint mark is now at a 90°angle to the front.


13. INSTALL STIFFENING CRANKCASE ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and crankcase.

  1. A112261E02
    Place a new O-ring on the cylinder block as shown in the illustration.

  1. A091021E02
    With the No. 1 crank pin of the crankshaft placed at the 6 o'clock position, install the No. 1 and No. 2 balance shafts and align the adjusting holes as shown in the illustration.

  1. A112260E01
    Apply a continuous bead of seal packing (Diameter 2.5 to 3.0 mm (0.098 to 0.118 in.)) as shown in the illustration.

    Seal packing:
    Tayota Genuine Seal Packing Black, Three bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the crankcase within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the crankcase.

  1. A112229E02
    Temporarily install the crankcase with the 11 bolts.
    Item
    Bolt Length
    Bolt A
    112 mm (4.41 in.)
    Bolt B
    35 mm (1.38 in.)

  1. A112229E03
    Uniformly tighten the bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. A094194E01
    Confirm that the timing marks of the balance shafts are aligned when the key groove is placed at the 6 o'clock position, as shown in the illustration.


14. INSTALL ENGINE REAR OIL SEAL
  1. Apply multi-purpose grease to the lip of a new oil seal.

    NOTICE:
    Keep the lip of foreign objects.

  1. A077422E01
    Using SST and a hammer, tap in the new oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    1. Wipe any extra grease off the crankshaft.
    2. Do not tap the oil seal at an angle.


15. INSTALL NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)

  1. A036850E02
    Apply adhesive to 2 or 3 threads of the plug, and install it.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

    NOTICE:
    1. Install the plug within 3 minutes of applying adhesive.
    2. Do not add coolant for at least an hour after installing the plug.


16. INSTALL OIL CONTROL VALVE FILTER

  1. A128210E01
    Check that there are no foreign objects on the mesh part of the oil control valve filter.

  1. Using a 6 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


17. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A076531E04
    Apply adhesive to 2 or 3 threads of the drain cock.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. A098363E01
    After tightening the drain cock to the specified torque, turn the drain cock clockwise as shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Install the drain cock within 3 minutes of applying adhesive.
    1. Do not add coolant for at least an hour after installing the drain cock.
    1. Do not turn the drain cock by more than 1 revolution (360°) after tightening the drain cock to the specified torque.
    1. Do not loosen the drain cock after setting it correctly.


18. INSTALL CYLINDER HEAD GASKET

  1. A126929E01
    Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.

    NOTICE:
    1. Remove any oil from contact surface.
    1. Be careful of the installation direction.


19. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the head gasket.

    NOTICE:
    Place the cylinder head gently in order to avoid damaging the gasket.

  1. Install the cylinder head bolts.

    NOTICE:
    The cylinder head bolts are tightened in 2 successive steps.


    1. F050595E03
      Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.

    2. Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.

      Torque:
      78.5 N*m{ 800 kgf*cm , 58 ft.*lbf }

  1. A098364E01
    Mark the front of the cylinder head bolts with paint.

  1. Retighten the cylinder head bolts by 90°as shown in the illustration.

  1. Check that the paint mark is now at a 90°angle to the front.


20. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A090053E02
    Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve.

  1. A128171
    Install the camshaft timing oil control valve with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


21. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

  1. A098365E02
    Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.

  1. Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

    NOTICE:
    Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).

  1. Check that there is no clearance between the gear fringe and camshaft.

  1. Tighten the flange bolt with the camshaft timing gear fixed in place.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.


22. INSTALL NO. 2 CAMSHAFT TIMING SPROCKET

  1. A032167E01
    Clamp the camshaft in a vise, then install the camshaft timing sprocket with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Do not damage the camshaft.


23. INSTALL NO. 2 CAMSHAFT BEARING
  1. Clean the contact surface of the bearing and the cylinder head.

    NOTICE:
    Do not apply engine oil to the bearing its contact surface.

  1. A013383E01
    Install the No. 2 camshaft bearing onto the cylinder head.


24. INSTALL NO. 1 CAMSHAFT BEARING
  1. Clean the contact surface of the bearing and the bearing cap.

    NOTICE:
    Do not apply engine oil to the bearing its contact surface.

  1. A124773
    Align the bearing claw with the claw groove of No. 1 and No. 2 bearing cap, and push in the No. 1 camshaft bearing.


25. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. F050592E01
    Place the 2 camshafts on the cylinder head with the No. 1 cam lobes facing the directions shown in the illustration.

  1. F050591E01
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. F050596E02
    Using several steps, uniformly tighten the 20 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 1 and No. 2 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap

    NOTICE:
    1. Tighten the bolts after deciding the position in the thrust direction of the camshaft by the No. 1 and No. 2 bearing caps.
    1. Install the camshaft with the timing mark of the camshaft timing gear on top.


26. INSTALL OIL PUMP DRIVE GEAR

27. INSTALL OIL PUMP ASSEMBLY

  1. B011673E01
    Install a new gasket and the oil pump with the 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


28. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

  1. A098367E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    2. A052505E01
      Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.

  1. A094576E01
    Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.

  1. A098369E01
    Using SST and a hammer, tap in the crankshaft timing sprocket.
    SST
    09309-37010  

  1. A098370E01
    Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


29. INSTALL CRANKSHAFT TIMING SPROCKET

A128186

30. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A132570
    Install the chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


31. INSTALL CHAIN SUB-ASSEMBLY

  1. A098367E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    2. A052505E01
      Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.

  1. A094576E01
    Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.

  1. A098369E01
    Using SST and a hammer, tap in the crankshaft timing sprocket.
    SST
    09309-37010  

  1. A098370E01
    Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


32. INSTALL CHAIN TENSIONER SLIPPER

  1. A124787E01
    Install the chain tensioner slipper with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


33. INSTALL TIMING CHAIN GUIDE

  1. A077243E01
    Install the timing chain guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


34. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A124770
    Install the sensor plate with the "F" mark facing forward.


35. REPLACE TIMING CHAIN COVER OIL SEAL

HINT:
There are 2 methods to replace the oil seal.

  1. If the timing chain cover is removed from the cylinder block:

    1. A112248
      Using a screwdriver and hammer, tap out the oil seal.

    2. Apply multi-purpose grease to the lip of a new oil seal.

      NOTICE:
      Keep the lip free of foreign objects.

    3. A112249E02
      Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge.
      SST
      09223-22010  

      NOTICE:
      Do not tap the oil seal at an angle.

  1. If the timing chain cover oil seal is installed to the cylinder block:

    1. Remove fan and generator V belt (Click here).

    2. Remove the crankshaft pulley (Click here).

    3. A077418E02
      Using a knife, cut off the lip of the oil seal.

    4. Using a screwdriver with its tip wrapped with tape, pry out the oil seal.

      NOTICE:
      After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.

    5. Apply multi-purpose grease to the lip of a new oil seal.

      NOTICE:
      Keep the lip free of foreign objects.

    6. A077419E02
      Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge.
      SST
      09223-22010  

      NOTICE:
      Do not tap the oil seal at an angle.

    7. Install the crankshaft pulley (Click here).

    8. Install the fan and generator V belt (Click here).


36. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

  1. A094577E01
    Apply seal packing (Diameter 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the chain cover.

  1. Apply a continuous bead of seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.

    1. Do not add engine oil for at least 2 hours after installing the chain cover.

      A132566E02

  1. A132568E03
    Install the timing chain cover with the 12 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt A
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B
    55 N*m{ 561 kgf*cm , 41 ft.*lbf } for bolt C
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

    HINT:
    Bolt length:
    Bolt A
    30 mm (1.18 in.) length for 10 mm head
    Bolt B
    30 mm (1.18 in.) length for 12 mm head
    Bolt C
    40 mm (1.57 in.) length for 14 mm head

  1. A014253E03
    Using an E10 "torx" socket, install the stud bolt for the V-ribbed belt tensioner.

    Torque:
    21.5 N*m{ 219 kgf*cm , 16 ft.*lbf }


37. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    When installing the chain tensioner, set the hook again if the hook releases the plunger.


38. INSTALL CRANKSHAFT PULLEY

  1. A098346E01
    Using SST, fix the pulley in place and tighten the bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }

  1. A112204E02
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E02
    Turn the crankshaft clockwise, then check that the plunger is extended.


39. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.

  1. A114332E01
    Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. Install the oil pan to the cylinder block.

  1. A114333E01
    Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A061184E04
    Place a transmission jack underneath the engine, then put a wooden block on the jack.

  1. Remove the chain block and sling device.

  1. Remove the No. 1 and No. 2 engine hangers.


40. INSTALL OIL PAN DRAIN PLUG

  1. A128176
    Place a new gasket on the oil pan drain plug, then install it onto the oil pan.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


41. INSTALL WATER PUMP ASSEMBLY
  1. Remove any old seal packing material from the contact surface.

  1. A094495E03
    Apply a continuous line of seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    Standard seal diameter:
    2.2 to 2.5 mm (0.09 to 0.10 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. The parts must be set within 3 minutes after applying seal packing. Otherwise, the material must be removed and reapplied.

  1. Install the water pump and clamp bracket with the 4 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the wire of the crankshaft position sensor onto the clamp bracket.

  1. Install the clamp of the crankshaft position sensor onto the water pump.


42. INSTALL WATER PUMP PULLEY

A098715E02
  1. Using SST, install the water pump pulley with the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-00700)

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


43. INSTALL CRANKSHAFT POSITION SENSOR

A095434E01

NOTICE:
Make sure that the O-ring is not cracked or jammed when installing it.

  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. A124557
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 90 kgf*cm , 80 in.*lbf }

  1. Connect the sensor connector.


44. INSTALL OIL FILTER UNION

  1. A126912E01
    Using a 12 mm hexagon wrench, install the oil filter union.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf }


45. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. A124763E03
    Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. Using SST, tighten the oil filter.

    SST
    09228-06501  

    1. Depending on the work space available, choose from the following.
      1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17.2 N*m{ 175 kgf*cm , 13 ft.*lbf }

      2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.


46. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A098345E09
    Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.


47. CHECK VALVE CLEARANCE

  1. A098170E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.21 to 0.27 mm (0.0083 to 0.0106 in.)
      Exhaust
      0.38 to 0.48 mm (0.0150 to 0.0189 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.

  1. Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.

  1. A098171E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.21 to 0.27 mm (0.0083 to 0.0106 in.)
      Exhaust
      0.38 to 0.48 mm (0.0150 to 0.0189 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


48. ADJUST VALVE CLEARANCE
  1. Remove the No. 2 camshaft (Click here).

  1. Remove the camshaft (Click here).

  1. Remove the valve lifters.

  1. A001082E01
    Using a micrometer, measure the thickness of the removed valve lifters.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.

    New lifter thickness:
    Item
    Specification
    Intake
    A = B + (C - 0.24 mm (0.0095 in.))
    Exhaust
    A = B + (C - 0.35 mm (0.0138 in.))

    A
    New lifter thickness
    B
    Used lifter thickness
    C
    Measured valve clearance
    CALCULATION EXAMPLE (Intake):
    1. Measured intake valve clearance = 0.16 mm (0.0063 in.)
      (Measured - Specification = Excess clearance)
      1. 0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
    2. Measured used lifter measurement = 5.250 mm (0.2067 in.)
    3. New lifter thickness = 5.410 mm (0.2130 in.)
      (Excess clearance + Used lifter thickness = Ideal new lifter)
      1. 0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
    4. Closest new lifter = 5.420 mm (0.2134 in.)
      1. Select No. 42 lifter

  1. Select a new lifter with a thickness as close as possible to the calculated values.

    HINT:
    1. Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).

    2. A126901E01
      The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.)

  1. Valve lifter selection chart (intake).

    A126931E02

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard intake valve clearance (cold):
    0.21 to 0.27 mm (0.0083 to 0.0106 in.)

    EXAMPLE:
    The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.

  1. Valve lifter selection chart (exhaust).

    A114356E01

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard exhaust valve clearance (cold):
    0.38 to 0.48 mm (0.0150 to 0.0189 in.)

    EXAMPLE:
    The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.

  1. Install the selected valve lifter.


49. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. A098176E03
    Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.

  1. A098177E03
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.

  1. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

  1. A098177E06
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 1 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap


50. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.

  1. A098178E03
    Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.

  1. A052473E01
    While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.

  1. A098174E05
    Examine the front marks, and numbers and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098174E07
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 2 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap

  1. A098173E04
    While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Be careful not to damage the valve lifter.

  1. A098180E04
    Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.


51. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    When installing the chain tensioner, set the hook again if the hook releases the plunger.


52. INSTALL CYLINDER HEAD COVER GASKET

  1. A128166
    Install the gasket onto the cylinder head cover.


53. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. A094204E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt A
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt B
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the clamp of the engine wire (labeled B).

  1. A112209
    Connect the 2 ventilation hoses to the cylinder head cover.


54. INSTALL OIL FILLER CAP SUB-ASSEMBLY

  1. A128159
    Install the gasket to the cap.

  1. A128158
    Install the oil filler cap.

    Torque:
    3.0 N*m{ 31 kgf*cm , 26 in.*lbf }


55. INSTALL SPARK PLUG

A132575

Torque:
25 N*m{ 254 kgf*cm , 18 ft.*lbf }


56. INSTALL IGNITION COIL ASSEMBLY

  1. A124400
    Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 4 ignition coil connectors.


57. INSTALL VENTILATION VALVE SUB-ASSEMBLY

  1. A092670E03
    Apply adhesive to the threads of the ventilation valve.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. A098067E01
    Using a 22 mm deep socket wrench, install the ventilation valve.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


58. INSTALL OIL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring and install it onto the guide.

  1. A112218E01
    Install the guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


59. INSTALL OIL DIPSTICK

60. INSTALL CAMSHAFT POSITION SENSOR

  1. A114368
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


61. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

  1. A114367E01
    Using SST, install a new gasket and the ECT sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    SST
    09817-33190  


62. INSTALL OIL PRESSURE SWITCH ASSEMBLY
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. A114362
    Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


63. INSTALL RADIO SETTING CONDENSER

  1. A112227
    Install the condenser with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


64. INSTALL KNOCK SENSOR

  1. A095427E01
    Install the sensor with the nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the knock sensor is in the correct position.

  1. Connect the sensor connector.


65. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A090053E01
    Apply a light coat of engine oil to the O-ring of the oil control valve.

  1. A124556
    Install the oil control valve with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed.

  1. Connect the oil control valve connector.


66. INSTALL ENGINE OIL COOLER (w/ Oil Cooler)
  1. Clean the oil cooler contact surface on the cooler mounting.

  1. A124389E01
    Install a new O-ring to the oil cooler.

  1. Apply a light coat of engine oil on the threads and under the head of the union bolt.

  1. A114329
    Install the oil cooler with the plate washer, union bolt and nut.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for union bolt
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut

  1. Connect the 2 oil cooler hoses.


67. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A112212
    Install the V-ribbed belt tensioner with the bolt and nut.

    Torque:
    59.5 N*m{ 607 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Do not lift the engine more than necessary.


68. INSTALL UNION BOLT (w/ Oil Cooler)
  1. Apply adhesive to the threads of the union bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. A129331
    Install the union bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


69. INSTALL OIL COOLER PIPE (w/ Oil Cooler)

  1. A126879
    Install a new gasket and the pipe with the bolt and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A126942E03
    Connect the No. 3 and No. 4 water by-pass hose to the oil cooler.


70. INSTALL NO. 1 WATER BY-PASS PIPE

  1. A112226
    Install a new gasket and the pipe with the bolt and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


71. INSTALL THERMOSTAT
  1. Install a new gasket onto the thermostat.

  1. A112199E02
    Install the thermostat with the jiggle valve upward.

    HINT:
    The jiggle valve may be set to within 10° on either side of the prescribed position.


72. INSTALL WATER INLET

  1. A112181
    Install the water inlet with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


73. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Install a new gasket onto the cylinder head.

  1. Temporarily tighten the exhaust manifold converter with the 5 nuts.

  1. A112190E01
    Tighten the 5 nuts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


74. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A112189
    Install the exhaust manifold heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. A098744E01
    Connect the air-fuel ratio sensor connector.


75. INSTALL NO. 2 MANIFOLD STAY

  1. A112192
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


76. INSTALL MANIFOLD STAY

  1. A112193
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


77. INSTALL IDLER PULLEY

  1. A132481
    Install the idler bracket with the 2 bolts.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

← REASSEMBLY (Nov 2005 – Dec 2006)REASSEMBLY (from Aug 2007) →