Using a small screwdriver, install a new snap ring onto one end of the piston pin hole.
HINT:
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
Gradually heat the piston up to 80 to 90°C (176 to 194°F).
Align the front marks of the piston and connecting rod, then push in the piston pin with your thumb until the pin comes into contact with the snap pin hole.
HINT:
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
2.
INSTALL PISTON RING SET
Install the expander and oil ring by hand.
HINT:
Install the expander and oil ring so that their ring ends are at opposite sides.
Securely install the expander to the oil ring's inner groove.
Using a piston ring expander, install the 2 compression rings with the paint mark as shown in the illustration.
NOTICE:
Install the No. 2 compression ring with the cord mark (2N) facing upward.
Position the piston rings so that the ring ends are as shown in the illustration.
3.
INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Install the 4 oil nozzles with the 4 bolts.
Torque:
7.0 N*m{
71 kgf*cm
, 62 in.*lbf
}
4.
INSTALL CYLINDER BLOCK WATER JACKET SPACER
5.
INSTALL CRANKSHAFT BEARING
Install the upper bearing with an oil groove onto the cylinder block.
NOTICE:
Do not apply engine oil to the bearing its contact surface.
6.
INSTALL NO. 2 CRANKSHAFT BEARING
Install the lower bearing onto the bearing cap.
NOTICE:
Do not apply engine oil to the bearing its contact surface.
7.
INSTALL CRANKSHAFT THRUST WASHER UPPER
Install the 2 thrust washers onto the No. 3 journal position of the cylinder block with the oil groove facing outward.
8.
INSTALL CRANKSHAFT
Apply engine oil to the upper bearing, and install the crankshaft onto the cylinder block.
Examine the front marks and numbers, and install the bearing caps onto the cylinder block in the order shown in the illustration.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
Mark the front of the bearing cap bolts with paint.
Retighten the 10 bearing cap bolts by 90° in the same sequence.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
9.
INSTALL CONNECTING ROD BEARING
Align the bearing claw with the oil groove of the connecting rod or connecting rod cap.
NOTICE:
Do not apply engine oil to the bearing or its contact surface.
10.
INSTALL PISTON WITH CONNECTING ROD
Apply engine oil to the cylinder walls, pistons, and surfaces of connecting rod bearings.
Check the position of the piston ring ends.
Using a hammer handle and piston ring compressor, press a piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.
Check that the front mark of the connecting rod cap is facing in the correct direction.
NOTICE:
Match the numbered connecting rod cap with the connecting rod.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
Using a 12 mm socket wrench, tighten the bolts in several passes to the specified torque.
Torque:
24.5 N*m{
250 kgf*cm
, 18 ft.*lbf
}
Mark the front of the connecting rod bolts with paint.
Retighten the cap bolts 90°as shown in the illustration.
Check that the crankshaft turns smoothly.
11.
INSTALL BALANCE SHAFT BEARING
Align the bearing claw with the claw groove, and push in the 8 bearings.
NOTICE:
Do not apply engine oil to the bearing its contact surface.
Apply a light coat of engine oil in the bearings.
12.
INSTALL BALANCE SHAFT
Rotate the No. 1 driven gear of the No. 1 balance shaft in the rotating direction until it hits the stopper.
Confirm that the timing marks on the No. 1 and No. 2 driven gears are aligned.
Align the timing marks of the No. 1 and No. 2 balance shafts as shown in the illustration.
Place the No. 1 and No. 2 balance shafts onto the crankcase.
Apply a light coat of engine oil to the threads and under the heads of the bolts.
Using several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.
Torque:
21.6 N*m{
220 kgf*cm
, 16 ft.*lbf
}
Mark the front of the bolts with paint.
Retighten the bolts 90°as shown in the illustration.
Check that the paint mark is now at a 90°angle to the front.
13.
INSTALL STIFFENING CRANKCASE ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and crankcase.
Place a new O-ring on the cylinder block as shown in the illustration.
With the No. 1 crank pin of the crankshaft placed at the 6 o'clock position, install the No. 1 and No. 2 balance shafts and align the adjusting holes as shown in the illustration.
Apply a continuous bead of seal packing (Diameter 2.5 to 3.0 mm (0.098 to 0.118 in.)) as shown in the illustration.
Seal packing:
Tayota Genuine Seal Packing Black, Three bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the crankcase within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the crankcase.
Temporarily install the crankcase with the 11 bolts.
Item
Bolt Length
Bolt A
112 mm (4.41 in.)
Bolt B
35 mm (1.38 in.)
Uniformly tighten the bolts.
Torque:
24 N*m{
245 kgf*cm
, 18 ft.*lbf
}
Confirm that the timing marks of the balance shafts are aligned when the key groove is placed at the 6 o'clock position, as shown in the illustration.
14.
INSTALL ENGINE REAR OIL SEAL
Apply multi-purpose grease to the lip of a new oil seal.
NOTICE:
Keep the lip of foreign objects.
Using SST and a hammer, tap in the new oil seal until its surface is flush with the rear oil seal retainer edge.
Apply adhesive to 2 or 3 threads of the plug, and install it.
Torque:
26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent
NOTICE:
Install the plug within 3 minutes of applying adhesive.
Do not add coolant for at least an hour after installing the plug.
16.
INSTALL OIL CONTROL VALVE FILTER
Check that there are no foreign objects on the mesh part of the oil control valve filter.
Using a 6 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the plug.
Torque:
30 N*m{
306 kgf*cm
, 22 ft.*lbf
}
17.
INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the drain cock.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent
After tightening the drain cock to the specified torque, turn the drain cock clockwise as shown in the illustration.
Torque:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
NOTICE:
Install the drain cock within 3 minutes of applying adhesive.
Do not add coolant for at least an hour after installing the drain cock.
Do not turn the drain cock by more than 1 revolution (360°) after tightening the drain cock to the specified torque.
Do not loosen the drain cock after setting it correctly.
18.
INSTALL CYLINDER HEAD GASKET
Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.
NOTICE:
Remove any oil from contact surface.
Be careful of the installation direction.
19.
INSTALL CYLINDER HEAD SUB-ASSEMBLY
Place the cylinder head on the head gasket.
NOTICE:
Place the cylinder head gently in order to avoid damaging the gasket.
Install the cylinder head bolts.
NOTICE:
The cylinder head bolts are tightened in 2 successive steps.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.
Torque:
78.5 N*m{
800 kgf*cm
, 58 ft.*lbf
}
Mark the front of the cylinder head bolts with paint.
Retighten the cylinder head bolts by 90°as shown in the illustration.
Check that the paint mark is now at a 90°angle to the front.
20.
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve.
Install the camshaft timing oil control valve with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
21.
INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.
Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.
NOTICE:
Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).
Check that there is no clearance between the gear fringe and camshaft.
Tighten the flange bolt with the camshaft timing gear fixed in place.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.
22.
INSTALL NO. 2 CAMSHAFT TIMING SPROCKET
Clamp the camshaft in a vise, then install the camshaft timing sprocket with the bolt.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
NOTICE:
Do not damage the camshaft.
23.
INSTALL NO. 2 CAMSHAFT BEARING
Clean the contact surface of the bearing and the cylinder head.
NOTICE:
Do not apply engine oil to the bearing its contact surface.
Install the No. 2 camshaft bearing onto the cylinder head.
24.
INSTALL NO. 1 CAMSHAFT BEARING
Clean the contact surface of the bearing and the bearing cap.
NOTICE:
Do not apply engine oil to the bearing its contact surface.
Align the bearing claw with the claw groove of No. 1 and No. 2 bearing cap, and push in the No. 1 camshaft bearing.
25.
INSTALL CAMSHAFT
Apply a light coat of engine oil to the journal portion of the camshaft.
Place the 2 camshafts on the cylinder head with the No. 1 cam lobes facing the directions shown in the illustration.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 20 bearing cap bolts in the sequence shown in the illustration.
Torque:
29.5 N*m{
301 kgf*cm
, 22 ft.*lbf
}
for No. 1 and No. 2 bearing cap
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
for No. 3 bearing cap
NOTICE:
Tighten the bolts after deciding the position in the thrust direction of the camshaft by the No. 1 and No. 2 bearing caps.
Install the camshaft with the timing mark of the camshaft timing gear on top.
26.
INSTALL OIL PUMP DRIVE GEAR
27.
INSTALL OIL PUMP ASSEMBLY
Install a new gasket and the oil pump with the 3 bolts.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
28.
INSTALL NO. 2 CHAIN SUB-ASSEMBLY
Set the No. 1 cylinder to TDC/compression.
Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.
Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.
Using SST and a hammer, tap in the crankshaft timing sprocket.
SST
09309-37010
Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
29.
INSTALL CRANKSHAFT TIMING SPROCKET
30.
INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the chain vibration damper with the 2 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
31.
INSTALL CHAIN SUB-ASSEMBLY
Set the No. 1 cylinder to TDC/compression.
Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.
Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.
Using SST and a hammer, tap in the crankshaft timing sprocket.
SST
09309-37010
Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
32.
INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper with the bolt.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
33.
INSTALL TIMING CHAIN GUIDE
Install the timing chain guide with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
34.
INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Install the sensor plate with the "F" mark facing forward.
35.
REPLACE TIMING CHAIN COVER OIL SEAL
HINT:
There are 2 methods to replace the oil seal.
If the timing chain cover is removed from the cylinder block:
Using a screwdriver and hammer, tap out the oil seal.
Apply multi-purpose grease to the lip of a new oil seal.
NOTICE:
Keep the lip free of foreign objects.
Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge.
SST
09223-22010
NOTICE:
Do not tap the oil seal at an angle.
If the timing chain cover oil seal is installed to the cylinder block:
Install the fan and generator V belt (Click here).
36.
INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
Apply seal packing (Diameter 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the chain cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the chain cover.
Apply a continuous bead of seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the chain cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the chain cover.
Install the timing chain cover with the 12 bolts and 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
for bolt A
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
for bolt B
55 N*m{
561 kgf*cm
, 41 ft.*lbf
}
for bolt C
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
for nut
HINT:
Bolt length:
Bolt A
30 mm (1.18 in.) length for 10 mm head
Bolt B
30 mm (1.18 in.) length for 12 mm head
Bolt C
40 mm (1.57 in.) length for 14 mm head
Using an E10 "torx" socket, install the stud bolt for the V-ribbed belt tensioner.
Torque:
21.5 N*m{
219 kgf*cm
, 16 ft.*lbf
}
37.
INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
Install a new gasket and the chain tensioner with the 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
NOTICE:
When installing the chain tensioner, set the hook again if the hook releases the plunger.
38.
INSTALL CRANKSHAFT PULLEY
Using SST, fix the pulley in place and tighten the bolt.
SST
09213-54015
(91651-60855)
09330-00021
Torque:
180 N*m{
1,835 kgf*cm
, 133 ft.*lbf
}
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
Turn the crankshaft clockwise, then check that the plunger is extended.
39.
INSTALL OIL PAN SUB-ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the oil pan.
Install the oil pan to the cylinder block.
Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Place a transmission jack underneath the engine, then put a wooden block on the jack.
Remove the chain block and sling device.
Remove the No. 1 and No. 2 engine hangers.
40.
INSTALL OIL PAN DRAIN PLUG
Place a new gasket on the oil pan drain plug, then install it onto the oil pan.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
41.
INSTALL WATER PUMP ASSEMBLY
Remove any old seal packing material from the contact surface.
Apply a continuous line of seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
Standard seal diameter:
2.2 to 2.5 mm (0.09 to 0.10 in.)
NOTICE:
Remove any oil from the contact surface.
The parts must be set within 3 minutes after applying seal packing. Otherwise, the material must be removed and reapplied.
Install the water pump and clamp bracket with the 4 bolts and 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Install the wire of the crankshaft position sensor onto the clamp bracket.
Install the clamp of the crankshaft position sensor onto the water pump.
42.
INSTALL WATER PUMP PULLEY
Using SST, install the water pump pulley with the 4 bolts.
SST
09960-10010
(09962-01000, 09963-00700)
Torque:
26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
43.
INSTALL CRANKSHAFT POSITION SENSOR
NOTICE:
Make sure that the O-ring is not cracked or jammed when installing it.
Apply a light coat of engine oil to the O-ring of the sensor.
Install the sensor with the bolt.
Torque:
9.0 N*m{
90 kgf*cm
, 80 in.*lbf
}
Connect the sensor connector.
44.
INSTALL OIL FILTER UNION
Using a 12 mm hexagon wrench, install the oil filter union.
Torque:
29.5 N*m{
301 kgf*cm
, 22 ft.*lbf
}
45.
INSTALL OIL FILTER SUB-ASSEMBLY
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
Using SST, tighten the oil filter.
SST
09228-06501
Depending on the work space available, choose from the following. 1. If enough space is available, use a torque wrench to tighten the oil filter.
Torque:
17.2 N*m{
175 kgf*cm
, 13 ft.*lbf
}
2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.
46.
SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.
Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration. If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.
47.
CHECK VALVE CLEARANCE
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.21 to 0.27 mm (0.0083 to 0.0106 in.)
Exhaust
0.38 to 0.48 mm (0.0150 to 0.0189 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.21 to 0.27 mm (0.0083 to 0.0106 in.)
Exhaust
0.38 to 0.48 mm (0.0150 to 0.0189 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
Measured used lifter measurement = 5.250 mm (0.2067 in.)
New lifter thickness = 5.410 mm (0.2130 in.) (Excess clearance + Used lifter thickness = Ideal new lifter)
0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
Closest new lifter = 5.420 mm (0.2134 in.)
Select No. 42 lifter
Select a new lifter with a thickness as close as possible to the calculated values.
HINT:
Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).
The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.)
Valve lifter selection chart (intake).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard intake valve clearance (cold):
0.21 to 0.27 mm (0.0083 to 0.0106 in.)
EXAMPLE: The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.
Valve lifter selection chart (exhaust).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard exhaust valve clearance (cold):
0.38 to 0.48 mm (0.0150 to 0.0189 in.)
EXAMPLE: The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.
Install the selected valve lifter.
49.
INSTALL CAMSHAFT
Apply a light coat of engine oil to the journal portion of the camshaft.
Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
29.5 N*m{
301 kgf*cm
, 22 ft.*lbf
}
for No. 1 bearing cap
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
for No. 3 bearing cap
50.
INSTALL NO. 2 CAMSHAFT
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.
While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.
Examine the front marks, and numbers and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
29.5 N*m{
301 kgf*cm
, 22 ft.*lbf
}
for No. 2 bearing cap
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
for No. 3 bearing cap
While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
NOTICE:
Be careful not to damage the valve lifter.
Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.
51.
INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
Install a new gasket and the chain tensioner with the 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
NOTICE:
When installing the chain tensioner, set the hook again if the hook releases the plunger.
52.
INSTALL CYLINDER HEAD COVER GASKET
Install the gasket onto the cylinder head cover.
53.
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply seal packing to the 2 locations shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the oil pan.
Install the cylinder head cover with the 8 bolts and 2 nuts.
Torque:
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
for bolt A
14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
for bolt B
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
for nut
Install the 2 engine wires with the 2 bolts.
Torque:
8.4 N*m{
86 kgf*cm
, 74 in.*lbf
}
Connect the clamp of the engine wire (labeled B).
Connect the 2 ventilation hoses to the cylinder head cover.
54.
INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the gasket to the cap.
Install the oil filler cap.
Torque:
3.0 N*m{
31 kgf*cm
, 26 in.*lbf
}
55.
INSTALL SPARK PLUG
Torque:
25 N*m{
254 kgf*cm
, 18 ft.*lbf
}
56.
INSTALL IGNITION COIL ASSEMBLY
Install the 4 ignition coils with the 4 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Connect the 4 ignition coil connectors.
57.
INSTALL VENTILATION VALVE SUB-ASSEMBLY
Apply adhesive to the threads of the ventilation valve.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent
Using a 22 mm deep socket wrench, install the ventilation valve.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
58.
INSTALL OIL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring and install it onto the guide.
Install the guide with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
59.
INSTALL OIL DIPSTICK
60.
INSTALL CAMSHAFT POSITION SENSOR
Install the sensor with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
61.
INSTALL ENGINE COOLANT TEMPERATURE SENSOR
Using SST, install a new gasket and the ECT sensor.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
SST
09817-33190
62.
INSTALL OIL PRESSURE SWITCH ASSEMBLY
Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent
Using a 24 mm deep socket wrench, install the oil pressure switch.
Torque:
13 N*m{
133 kgf*cm
, 10 ft.*lbf
}
63.
INSTALL RADIO SETTING CONDENSER
Install the condenser with the bolt.
Torque:
10 N*m{
102 kgf*cm
, 7 ft.*lbf
}
64.
INSTALL KNOCK SENSOR
Install the sensor with the nut.
Torque:
20 N*m{
205 kgf*cm
, 15 ft.*lbf
}
NOTICE:
Make sure that the knock sensor is in the correct position.
Connect the sensor connector.
65.
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to the O-ring of the oil control valve.
Install the oil control valve with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
NOTICE:
Make sure that the O-ring is not cracked or jammed.
Connect the oil control valve connector.
66.
INSTALL ENGINE OIL COOLER (w/ Oil Cooler)
Clean the oil cooler contact surface on the cooler mounting.
Install a new O-ring to the oil cooler.
Apply a light coat of engine oil on the threads and under the head of the union bolt.
Install the oil cooler with the plate washer, union bolt and nut.
Torque:
29.5 N*m{
301 kgf*cm
, 22 ft.*lbf
}
for union bolt
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
for nut
Connect the 2 oil cooler hoses.
67.
INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Install the V-ribbed belt tensioner with the bolt and nut.
Torque:
59.5 N*m{
607 kgf*cm
, 44 ft.*lbf
}
NOTICE:
Do not lift the engine more than necessary.
68.
INSTALL UNION BOLT (w/ Oil Cooler)
Apply adhesive to the threads of the union bolt.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent
Install the union bolt.
Torque:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
69.
INSTALL OIL COOLER PIPE (w/ Oil Cooler)
Install a new gasket and the pipe with the bolt and 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Connect the No. 3 and No. 4 water by-pass hose to the oil cooler.
70.
INSTALL NO. 1 WATER BY-PASS PIPE
Install a new gasket and the pipe with the bolt and 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
71.
INSTALL THERMOSTAT
Install a new gasket onto the thermostat.
Install the thermostat with the jiggle valve upward.
HINT:
The jiggle valve may be set to within 10° on either side of the prescribed position.