Only Wireless Control Function is Inoperative
Circuit diagnosis · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The door control receiver receives signals from the transmitter and sends these signals to the main body ECU via the certification ECU using the serial line. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the FLSH relay*1 (turn signal flasher relay*2).- HINT:
- *1: for LHD
- *2: for RHD
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRELESS DOOR LOCK FUNCTION |
Check the wireless door lock control functions (Click here).
- OK:
- Each function of wireless door lock control system operates normally using transmitter switches.
|
|
||||
| NG | |
| 2. CHECK TRANSMITTER LED ILLUMINATION |
Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.
- OK:
- Transmitter's LED illuminates 3 times when switch is pressed 3 times.
|
|
||||
| NG | |
| 3. REPLACE TRANSMITTER BATTERY |
Temporarily replace the transmitter battery with a new or normally functioning one (Click here).
Check that the doors can be locked and unlocked using the transmitter switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| NG | |
| 4. SWITCH TO SELF-DIAGNOSTIC MODE |
![]() ![]() |
Switch to self-diagnostic mode.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Check that the system has switched to self-diagnostic mode by checking wireless door lock buzzer sound pattern.
- OK:
- Sound pattern is same as illustration.
|
|
||||
| OK | |
| 5. CHECK BY SELF-DIAGNOSTIC MODE |


Check the diagnostic outputs when the door control transmitter switch is held down. The diagnostic outputs can be checked by the flash patterns of the room light.
Result: Result
Proceed to
Unmatching recognition code is output
A
Normal waves (buzzer sound patterns) is output
B
No diagnosis outputs
C
|
|
||||
|
|
||||
| A | |
| 6. REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.
- OK:
- System can switch to rewrite mode or Add mode and that recognition code can be registered.
|
|
||||
| OK | ||
| ||
| 7. CHECK DOOR CONTROL RECEIVER (RESPONSE) |
Temporarily replace the door control receiver with a new or normally functioning one (Click here, Click here).
Held down the door control transmitter's switch.
Check that an unmatching recognition code is output.
- OK:
- Unmatching recognition code is output.
|
|
||||
| NG | |
| 8. CHECK DOOR CONTROL RECEIVER (OUTPUT) |
![]() ![]() |
Measure the voltage of the connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
L13-5 (DATA) - Body ground
Transmitter switch ON → OFF (No key in cabin, all doors closed)
Below 1 V → 6 to 7 V → Below 1 V
|
|
||||
| OK | |
| 9. CHECK WIRE HARNESS (CERTIFICATION ECU -DOOR CONTROL RECEIVER) |
![]() ![]() |
Disconnect the E63 ECU connector.
Disconnect the L13 receiver connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E63-38 (RDA) - L13-5 (DATA)
Below 1 Ω
E63-39 (RSSI) - L13-2 (RSSI)
E63-29 (RCO) - L13-4 (+5)
E63-38 (RDA) or L13-5 (DATA) - Body ground
10 kΩ or higher
E63-39 (RSSI) or L13-2 (RSSI) - Body ground
E63-29 (RCO) or L13-4 (+5) - Body ground
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (MAIN BODY ECU - CERTIFICATION ECU) |
![]() ![]() |
Disconnect the E19 and E63 ECU connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E19-11 (CANN) - E63-27 (CANH)
Below 1 Ω
E12-12 (CANP) - E63-28 (CANL)
E19-11 (CANN) or E63-27 (CANH) - Body ground
10 kΩ or higher
E12-12 (CANP) or E63-28 (CANL) - Body ground
|
|
||||
| OK | |
| 11. CHECK DOOR CONTROL RECEIVER |
Temporarily replace the door lock control receiver with a new or normally functioning one (Click here, Click here).
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| NG | |
| 12. CHECK ECU AGGREGATION BOX (OPERATION) |
Temporarily replace the ECU aggregation box (certification ECU) with a new or normally one.
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
| 13. CONFIRM PROCEDURES TO ENTER SELF-DIAGNOSTIC MODE |
| Result |
Proceed to |
| Self-diagnostic mode entry successful |
A |
| Self-diagnostic mode entry unsuccessful |
B |
|
|
||||
| A | ||
| ||




