2005-2008 RAV4 · Service Manual SERVICE SPECIFICATIONS

SERVICE DATA

Specifications · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

Stop Light Switch 
Stop light switch
Click here
Resistance 1 - 2
Switch pin released
Below 1 Ω
Resistance 1 - 2
Switch pin pushed in
10 kΩ or higher
Brake Pedal Load Sensing Switch 
Brake pedal load sensing switch
Click here
Resistance 1 - 2
Brake pedal depressed
Approx. 1 kΩ
Resistance 1 - 2
Brake pedal released
Approx. 213 Ω
Brake Pedal 
Brake pedal height from dash panel
Click here
LHD
184.2 to 194.2 mm (7.252 to 7.646 in.)
RHD
168.6 to 178.6 mm (6.638 to 7.031 in.)
Stop light switch clearance
Click here
0.5 to 2.6 mm (0.020 to 0.102 in.)
Brake pedal free play
Click here
1.0 to 6.0 mm (0.039 to 0.236 in.)
Brake pedal reserve distance from dash panel
Click here
See the table below.
Brake Pedal Reserve Distance from Dash Panel 
Engine
VSC
LHD
RHD
1AZ-FE
without
More than 90 mm (3.54 in.)
More than 80 mm (3.15 in.)
with
More than 115 mm (4.53 in.)
More than 105 mm (4.13 in.)
2AZ-FE
without
More than 95 mm (3.74 in.)
More than 85 mm (3.34 in.)
with
More than 120 mm (4.72 in.)
More than 110 mm (4.32 in.)
2AD-FTV
without
More than 75 mm (2.95 in.)
More than 70 mm (2.75 in.)
with
More than 110 mm (4.33 in.)
More than 100 mm (3.93 in.)
2AD-FHV
without
More than 75 mm (2.95 in.)
More than 70 mm (2.75 in.)
with
More than 110 mm (4.33 in.)
More than 100 mm (3.93 in.)
Brake Fluid Level Warning Switch 
Brake fluid level warning switch
Click here
Resistance 1 - 2
Float up (Switch OFF)
10 kΩ or higher
Resistance 1 - 2
Float down (Switch ON)
Below 1 Ω
Brake Booster 
Booster push rod and pin head (SST) clearance
Click here
-0.21 to 0 mm (-0.0083 to 0 in.)
Vacuum Pump (for 2AD-FTV, 2AD-FHV) 
Vacuum pump negative pressure
Click here
More than 86.7 kPa (650 mmHg, 26 in.Hg)
Front Brake 
Pad lining thickness
Click here
Standard
12.0 mm (0.472 in.)
Minimum
1.0 mm (0.039 in.)
Disc thickness
Click here
10.83 inch disc
Standard
25.0 mm (0.984 in.)
Minimum
22.0 mm (0.866 in.)
11.70 inch disc
Standard
28.0 mm (1.102 in.)
Minimum
25.0 mm (0.984 in.)
Disc runout
Click here
Maximum
0.05 mm (0.0020 in.)
Rear Brake 
Pad lining thickness
Click here
Standard
10.5 mm (0.413 in.)
Minimum
1.0 mm (0.039 in.)
Disc thickness
Click here
Standard
12.0 mm (0.472 in.)
Minimum
10.5 mm (0.413 in.)
Disc runout
Click here
Maximum
0.15 mm (0.0059 in.)
← SERVICE DATA (Nov 2005 – Dec 2006)TORQUE SPECIFICATIONS (Nov 2005 – Dec 2006) →