B2342 Switch Failure
Diagnostic trouble codes · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
DESCRIPTION
This DTC is output when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE OPEN or TILT UP switch in the overhead junction block is stuck for 30 seconds or more.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2342 |
Sliding roof drive gear (sliding roof ECU) detects SLIDE OPEN or TILT UP switch in overhead junction block is stuck for 30 seconds or more |
|
WIRING DIAGRAM
Refer to DTC B2341 (Click here).INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (SLIDE OPEN AND TILT UP SWITCH) |
Use the Data List to check if the sliding roof control switch is functioning properly.
Sliding roof drive gear Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
Open Switch Failure (Current)
SLIDE OPEN switch condition (current) / Fail or Not Fail
Fail: SLIDE OPEN switch is stuck
Not Fail: SLIDE OPEN switch is not stuck
-
Close Switch Failure (Current)
TILT UP switch condition (current) / Fail or Not Fail
Fail: TILT UP switch is stuck
Not Fail: SLIDE OPEN switch is not stuck
-
Open Switch Failure (Past)
SLIDE OPEN switch condition (past) / Fail or Not Fail
Fail: SLIDE OPEN switch was stuck in past
Not Fail: SLIDE OPEN switch was not stuck in past
-
Close Switch Failure (past)
TILT UP switch condition (past) / Fail or Not Fail
Fail: TILT UP switch was stuck in past
Not Fail: TILT UP switch was not stuck in past
-
- OK:
- "Not Fail" appears on tester screen.
|
|
||||
| OK | |
| 2. CHECK SLIDING ROOF FUNCTION |
Check the auto operation with the SLIDE OPEN and TILT UP switch (Click here).
- OK:
- Auto operation operates normally with SLIDE OPEN and TILT UP switch.
|
|
||||
| OK | |
| 3. DELETE DTC |
Delete the DTC (Click here).
| NEXT | ||
| ||
| 4. INSPECT OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH) |
Remove the overhead junction block.

Measure the resistance of the switch.
- Standard resistance:
Tenter Connection
Switch Condition
Specified Condition
8 (UP) - 7 (GND)
TILT UP switch pushed
Below 1 Ω
8 (UP) - 7 (GND)
TILT UP switch not pushed
10 kΩ or higher
9 (DOWN) - 7 (GND)
SLIDE OPEN switch pushed
Below 1 Ω
9 (DOWN) - 7 (GND)
SLIDE OPEN switch not pushed
10 kΩ or higher
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 5. REPLACE OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH) |
Temporarily replace the overhead junction block (sliding roof control switch) with a new or normally functioning one (Click here).
| NEXT | |
| 6. DELETE DTC |
Delete the DTC (Click here).
| NEXT | ||
| ||
| 7. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
Check that the sliding roof drive gear can be initialized (Click here).
- OK:
- Sliding roof drive gear can be initialized.
|
|
||||
| OK | |
| 8. CHECK SLIDING ROOF FUNCTION |
Check the auto operation with the SLIDE OPEN and TILT OPEN switch (Click here).
- OK:
- Auto operation operates normally with SLIDE OPEN and TILT UP switch.
|
|
||||
| OK | |
| 9. DELETE DTC |
Delete the DTC (Click here).
| NEXT | ||
| ||
| 10. CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - OVERHEAD JUNCTION BLOCK) |
Disconnect the R9 ECU connector.

Disconnect the R8 junction block connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
R9-7 (DWN) - R8-9 (DOWN)
Below 1 Ω
R9-9 (UP) - R8-8 (UP)
Below 1 Ω
R8-7 (GND) - Body ground
Below 1 Ω
R8-9 (DOWN) - Body ground
10 kΩ or higher
R8-8 (UP) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
