ECD SYSTEM (for CCo) > VC Output Circuit |



| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch to ON.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
| Communication is possible | A |
| Communication is not possible | B |
|
| ||||
| B | |
| 3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the accelerator pedal position sensor connector.
|
| ||||
| B | |
| 4.CHECK MIL (DIESEL THROTTLE BODY ASSEMBLY) |
Disconnect the diesel throttle body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the diesel throttle body assembly connector.
|
| ||||
| B | |
| 5.CHECK MIL (FUEL PRESSURE SENSOR) |
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the fuel pressure sensor connector.
|
| ||||
| B | |
| 6.CHECK MIL (EGR VALVE ASSEMBLY) |
Disconnect the EGR valve assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the EGR valve assembly connector.
|
| ||||
| B | |
| 7.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the manifold absolute pressure sensor connector.
|
| ||||
| B | |
| 8.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY) |
Disconnect the battery current sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the battery current sensor connector.
|
| ||||
| B | |
| 9.CHECK HARNESS AND CONNECTOR |
Disconnect the accelerator pedal position sensor connector.
Disconnect the diesel throttle body assembly connector.
Disconnect the fuel pressure sensor connector.
Disconnect the EGR valve assembly connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the battery current sensor connector.
![]() |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A12-57 (VCP2) - Body ground | Always | 10 kΩ or higher |
| B32-97 (VCVL) - Body ground | Always | 10 kΩ or higher |
| B32-68 (VCM) - Body ground | Always | 10 kΩ or higher |
| B32-69 (VCS) - Body ground | Always | 10 kΩ or higher |
| B32-94 (VCEG) - Body ground | Always | 10 kΩ or higher |
| B32-93 (VCPM) - Body ground | Always | 10 kΩ or higher |
| B32-75 (VCIB) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the accelerator pedal position sensor connector.
Reconnect the diesel throttle body assembly connector.
Reconnect the fuel pressure sensor connector.
Reconnect the EGR valve assembly connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the battery current sensor connector.
Reconnect the ECM connectors.
|
| ||||
| OK | ||
| ||