DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition
| Trouble Area |
| P0705 |
|
|

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF |
| |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| |
| Shift SW Status (N Range) | PNP switch status/ ON or OFF |
| |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| |||
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| |||
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| 1.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B28-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| B28-1 (RB) - Body ground | Ignition switch off | Below 1 V |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (ECM OUTPUT SIGNAL) |
![]() |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B28-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| B28-4 (B) - Body ground | Ignition switch off | Below 1 V |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift lever in P | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever in N | Below 1 Ω |
| 1 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher |
| 1 (RB) - 2 (RL) | Shift lever not in R | 10 kΩ or higher |
| Shift lever not in N | 10 kΩ or higher |
| 1 (RB) - 7 (DL) | Shift lever not in D, M, "+" or "-" | 10 kΩ or higher |
| *1 | Component without harness connected (Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE) |
![]() |
Disconnect the transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E98-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| E98-3 (IG) - Body ground | Ignition switch off | Below 1 V |
| *1 | Front view of wire harness connector (to Transmission Control Switch) |
|
| ||||
| OK | |
| 5.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG) - 7 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever not in M, "+" or "-" | 10 kΩ or higher |
| *1 | Component without harness connected (Transmission Control Switch) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - ECM) |
![]() |
Disconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-77 (P) - Body ground |
| 11 to 14 V |
| B32-76 (R) - Body ground |
| 11 to 14 V* |
| B32-99 (N) - Body ground |
| 11 to 14 V |
| A12-47 (D) - Body ground |
| 11 to 14 V |
| B32-39 (S) - Body ground |
| 11 to 14 V |
| B32-77 (P) - Body ground |
| Below 1 V |
| B32-76 (R) - Body ground |
| Below 1 V |
| B32-99 (N) - Body ground |
| Below 1 V |
| A12-47 (D) - Body ground |
| Below 1 V |
| B32-39 (S) - Body ground |
| Below 1 V |
| *1 | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 7.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 8.PERFORM INITIALIZATION |
| Replaced Part |
|
Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).
Check that no DTC is stored.
| NEXT | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the park/neutral position switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B28-4 (B) - A12-25 (NSW) | Always | Below 1 Ω |
| B28-4 (B) - Body ground | Always | 10 kΩ or higher |
| A12-25 (NSW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B28-4 (B) - B32-51 (STAR) | Always | Below 1 Ω |
| B28-4 (B) - Body ground | Always | 10 kΩ or higher |
| B32-51 (STAR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
| *2 | Front view of wire harness connector (to ECM) |
| *3 | w/ Entry and Start System |
| *4 | Front view of wire harness connector (to ECM) |
| *5 | w/o Entry and Start System |
|
| ||||
| OK | |
| 10.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 11.PERFORM INITIALIZATION |
| Replaced Part |
|
Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).
Check that no DTC is stored.
| NEXT | ||
| ||