DTC P0500 Vehicle Speed Sensor "A" |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While vehicle being driven, no vehicle speed sensor signal to ECM. (1 trip detection logic) |
|

| 1.CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM) |
Disconnect the combination meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) - A12-8 (SPD) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) or A12-8 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK COMBINATION METER (+S VOLTAGE) |
![]() |
Disconnect the combination meter connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E22-39 (+S) - Body ground | Ignition switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Combination Meter) |
|
| ||||
| OK | |
| 5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM) |
![]() |
Move the shift lever to N.
Jack up the vehicle.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) - Body ground |
| Voltage generated intermittently |
|
| ||||
| OK | ||
| ||
| 6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM) |
![]() |
Move the shift lever to N.
Jack up the vehicle.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) - Body ground |
| Voltage generated intermittently |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU) |
Disconnect the combination meter connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) - A67-11 (SP1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) - A27-26 (SP1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) or A67-11 (SP1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) or A27-26 (SP1) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| NG | A |
| OK (w/ VSC) | B |
| OK (w/o VSC) | C |
|
| ||||
|
| ||||
| A | ||
| ||